What is the Advantage and Disadvantage of Bottom Pull Facial Tissue Paper Production Line

Grace

Jul. 21, 2025

Converting operations impact on tissue paper product properties

Costa Vieira, J., Fiadeiro, P. T., and Costa, A. P. (). "Converting operations impact on tissue paper product properties – A Review," BioResources 18(1), -.

Abstract

Tissue paper is deep-rooted in our daily life because of its different types of products that allow various applications. Tissue paper is a low grammage paper that is mainly characterized by softness, tensile strength, liquid absorption, and elasticity. These characteristics are essential when producing products such as toilet paper, kitchen rolls, hand towels, napkins, and facials. The tissue paper production involves two stages: formation of the tissue paper sheet itself and its converting into different finished products. Converting is characterized by several operations, namely: unwinding, winding, embossing, lamination, perforation, cutting, packaging, and palletizing. The most impacting operation is the embossing, which consists of marking a pattern on the paper sheet by applying pressure, with the intent to produce papers more aesthetically pleasing to the final consumer and/or a way to identify a particular brand. Also, it affects final properties, increasing the liquid absorption capacity and bulk but reducing softness and tensile strength. Converting is complex and has a huge impact on the finished products properties. In this review, the authors explored the different steps of converting and how they impact the different properties of finished tissue products.

If you are looking for more details, kindly visit our website.

Download PDF

Full Article

Converting Operations Impact on Tissue Paper Product Properties – A Review

Joana C. Vieira,* Paulo T. Fiadeiro, and Ana P. Costa

DOI: 10./biores.18.1.Vieira

Keywords: Converting operations; Embossing; Finishing; Paper properties; Perforation; Tissue paper; Winding

Contact information: Fiber Materials and Environmental Technologies (FibEnTech-UBI), Universidade da Beira Interior, R. Marquês D’Ávila e Bolama, -001 Covilhã, Portugal;

* Corresponding author:

INTRODUCTION

The tissue paper market has been expanding worldwide. This is explained by the consumption growth of hygiene products because of the increase in quality-of-life expectations. The main tissue paper products that can be found on the market include paper towels, napkins, facial tissues, and toilet paper, and they play an important role in modern life. These tissue paper products contribute to improving hygiene, comfort, and convenience in our society, helping to reduce the spread of diseases. Figure 1 presents the graph of evolution and forecast demand of consumption for domestic and sanitary tissue paper products, based on the data published by Lamberg et al. (), in the ten global regions considered, namely in the Northern and Western Europe, Southern Europe, Eastern Europe, the North America, South America, Africa, Western Asia, Southern Asia, South-Eastern Asia, and Eastern Asia.

Fig. 1. Consumption evolution and forecast demand of ton for domestic and sanitary tissue paper products in world regions between and

From the analysis of Fig. 1, it is relevant to point out that the consumption of tissue paper products in developed countries is more or less stable, while for developing countries, there is room for greater growth in these types of products. Figure 2 shows the growth rates as a pie chart of the main types of domestic and sanitary tissue paper products, based on the data published by Lamberg et al. (), in the global regions considered.

Fig. 2. Growth rates (%/year) of major types of household and sanitary tissue paper products in world regions

Figure 2 confirms the growth trend in consumption of these types of products, apart from Eastern Asia, where there is an inverse trend. The growth in demand for these products has led to an increase in the number of producers to satisfy the market and make it more competitive. For the companies to achieve a competitive advantage, they are always looking for continuous improvement, optimization of production processes, and reduction of operating costs, to increase product quality levels and satisfy customer requirements. An important factor in the tissue paper market segment is the satisfaction of customers, who look for softness as a main property in certain products or absorbency in others, depending on their final purpose (Vieira et al. a; Galli ). Thus, the properties of tissue paper must be in accordance with consumer requirements (Fig. 3). Tissue paper can then be defined as a cellulosic-based product composed of virgin and/or recycled fibers, produced with a low grammage, high flexibility, high bulk, creped, and depending on its application (toilet paper, paper towels, or napkins), embossed (Vieira et al. a; Galli ). Commercially, tissue paper products can be classified according to the purpose of use both at-home (referred to as “consumer” or At Home – AtH products) and away-from-home (referred to as HORECA products – HOtel REstaurants and Coffee, or Away From Home – AFH) (Galli ).

Fig. 3. Factors that affect tissue paper product consumer requirements (based on the data furnished by Galli )

It is through tissue paper conversion technology that, based on the requirements determined by the consumer, it is possible to produce finished paper products with the desired special properties and of high quality (Kimari ; Spina and Cavalcante ). The tissue paper converting process is characterized by several operations. The main ones include: unwinding, winding, printing, laminating, perforating, cutting, packaging, and palletizing (Kimari ; Cigolini and Rossi ). Products can be divided into two groups: rewound products, such as kitchen rolls and toilet paper, as they are unrolled and rolled up in the conversion process, and folded products such as napkins and handkerchiefs. The sequence of the converting operations for the rewound products can be seen in Fig. 4 and for the folded products in Fig. 5.

Fig. 4. Processes involved in converting the paper reel to the finished rewound products

Fig. 5. Processes involved in converting the paper reel to the finished folded products

Paper converting technology needs to deal with all these processes to give paper products special properties. One of the most important aspects to face during paper converting is the control of the production process, because of its nature as a continuous process. In fact, modern paper machines cannot operate efficiently without strict quality control of products and processes. One way to perform quality control is by analyzing process problems and automatically recommending effective corrections. This can be done by monitoring the paper converting operations, including the lamination of paper sheets, using a control program that gives the corresponding correction procedures. The paper properties are monitored by a set of actuator arrays, which act perpendicularly to the direction of movement of the paper sheet passing through the machine. Controller feedback is tailored to provide performance, ensuring robust uncertainty modeling. Basically, it is important to use both offline and online analyzes to define the characteristic product and process properties to guarantee the high quality of the final product (Spina and Cavalcante ). To better understand the converting process and how it impacts on the properties of the final product, a detailed analysis of each of the involved operations separately is presented in the following sections.

Unwinding

In the tissue paper industry, winders and rewinders are key components in the first stage of the complex converting process. Winding, unwinding, and then rewinding on a spool are, in fact, operations that require a precise execution to obtain a final product that, once wound, maintains the characteristics and quality resulting from the production process. This is due to the delicate nature of the material itself and the need to preserve the creping and density obtained in the production process to maintain the softness and bulk that distinguish it (Pejic ; D’Olivo ). The unwinders are responsible for unwinding the parent reel that leaves the tissue paper machine to obtain finished reels with smaller dimensions, the mother reels, if necessary. The reels used in tissue paper converting are generally heavy. It is possible to use coils with a length of 2 to 5 m and a diameter of up to about 3 m, with weights that can reach 5 tons (Paolinelli et al. ). The tissue paper converting machine may need up to four unwinders, as the final product is made up of several sheets. If the number of sheets of the finished product exceeds the number of unwinders of the converting machine, a mother reel with multiple sheets will be created using external rewinders. For example, in a converting machine with two unwinders, to produce a finished product of 3 sheets, you will have to feed the machine with a mother reel of 2 sheets and another with 1 sheet (Paolinelli et al. ). For tissue paper reels, the unwinding itself takes place via motorized belts, called peripheral unwinding. Each material has certain properties and characteristics that will affect the correct winding and/or unwinding process. An incorrect or inaccurate rewinding/unwinding process can cause permanent damage to the tissue paper sheet, where excessive elongation of the wound material implies substantial loss of desired characteristics such as crepe and bulk (D’Olivo ; A.Celli Group ).

Sheet tension control during the unwind/rewind operation is complex and subject to many variables. However, it is important to obtain proper control of the spool tension to avoid defects and compromise the properties of the sheet of paper. In addition, high-quality, automated tension control of the sheet is dependent on the traction provided by the machine’s idler rollers. It is important to identify the reasons behind the production problems in this section of the converting machine. As far as is known, winding defects occur less than 5% of the time. Table 1 presents the most common problems and the corresponding solutions that may occur (Williams ).

Table 1. Problems and Respective Solutions that May Occur in the Unwinding/Rewinding Operation (Williams )

For an automatic unwinder in which the spool is unwound through a combination of a peripheral and a central unwinder, the finished spool is lifted by motorized counterpoints of the central unwinder and placed on top of the unwinding station, to be later removed. Thus, through a shuttle, it is possible to insert a new spool into the unwind station. The central unwinder is double and has two pairs of tailstocks, thus allowing the first pair of tailstocks to be in the upper position when a spool is running low, while the second pair of tailstocks is available to engage the new spool inserted by the shuttle. In combination with the peripheral unwinder, it then allows the start of the unwinding of the sheet (Paolinelli et al. ). The tissue paper sheet is then routed to the embossing section for both rewound and folding products, and lamination in the case of rewound products.

Embossing / Lamination

According to the standard ISO -1 (), embossing is a converting operation by which a raised or depressed pattern is produced on a tissue paper sheet, generally by pressure between engraved rolls or between an engraved roll and an elastic or a deformable supporting surface. On the other hand, and considering the same standard, lamination is also a converting operation to join/bonding together two or more plies of a tissue paper sheet to form a multi-ply tissue product, which can be associated or not to the embossing process.

Embossing of tissue paper products is a sensitive process because of the presence of different factors such as flexibility, weight, softness, and attractive design of the paper (DeMaio and Patterson ; Pejic ). Therefore, several aspects of processing need to be addressed with control methodologies. Product quality also depends on various physical parameters such as temperature, humidity, and pressure.

Fig. 6. Images of the deco and micro engraving patterns and the corresponding embossed tissue paper sheets (Vieira et al. a)

The influence of geometrical and material parameters on the mechanical response of fibers used in papermaking is also critical (Kimari ; DeMaio and Patterson ). Embossing is an example of compressive formation on paper in the converting process. These can be stamped to increase the properties of the finished product, such as liquid absorption capacity, and softness. This process can produce papers with aesthetically pleasing designs, occasionally for the purpose of product identification distinguishing them from other competitors. Embossing is performed layer by layer, for instance, the deco and micro engravings can be produced on the top of a single layer or in several layers for a multi-layer paper. In general, the deco pattern appears on the top embossing roll and the micro pattern appears on the bottom embossing roll. The resulting product with more than one layer has properties that cannot be obtained in a paper with a single layer (Digby ). Figure 6 shows examples of the deco and micro engraving patterns and the corresponding embossed tissue paper sheets.

Embossing patterns for tissue papers serve to improve several properties such as porosity, hygroscopicity, thickness/bulk, flexibility, and absorbency. Embossing creates a graphic element allowing drawings to be raised or depressed on paper. A metallic cylinder (embossing roll) with a relief image engraved on its surface is pressed against the sheet(s) of paper (Fig. 7).

Fig. 7. Example of a steel embossing roll and its toilet paper LOG

Currently, several types of embossers are used, and the pressure, rubber hardness, temperature, and humidity of the paper can be varied to obtain different products (DeMaio and Patterson ; Biagiotti ).

During tissue paper production, the greatest bulk loss usually occurs in the pressing stage. Therefore, in the transformation process, the most common method that is used to increase bulk is dry embossing, but depending on the pressure used in this step, the bulk created can be short-lived, and it can also be lost when tissue paper is wetted again (Janda ). Each tissue paper fibrous composition has a predetermined limit to the embossing pressure, beyond which the strength properties of the sheet are destroyed, consequently impairing the runnability of the converting machine, and/or the quality requirements of the finished product. Thus, the tissue paper sheet loses engraving marks if embossing takes place in its elastic zone. In contrast, if the embossing is produced close to the breaking point of the sheet (excessive pressure applied), then the paper becomes fragile, which can cause failures in the converting process (Assis et al. ; Giannini ). As embossing is a mechanical compression process in the tissue paper converting, the pressure used is an operating condition that is essential to control to produce quality toilet paper (Spina and Cavalcante ). From the work developed by Vieira et al. (a), it was shown that the mechanical properties suffer a negative impact with the embossing operation in comparison with the corresponding industrial creped tissue paper sheet without embossing. In addition, the micro-embossing pattern was shown to have a greater impact on thickness, increase in volume, and loss of mechanical properties. From the same study developed by Vieira et al. (a), the authors concluded that there is an optimal pressure for the embossing process, in which the mechanical strength properties are maximized (through the densification of the tissue paper sheet) without impacting too much on the softness and absorption of liquids. This optimum pressure is the limit beyond which the structural degradation of the tissue paper sheet takes place. This study is in line with the previously mentioned in which the micro pattern is the one that most affects the structure of the sheet of paper. Contrastingly, from the samples under study, it was possible to perceive that the greater or lesser loss of mechanical properties or softness depends on their fibrous composition, since the industrial tissue paper samples used show different morphologies. In particular, one of them depicted a presence of recycled fibers/process broke.

With the evolution of the embossing and lamination process, different solutions have emerged until now, and the most common is the use of an engraved steel roller working against a roller with a rubber cover that can vary from 45 to 98 Sh-A (Shore-A means the hardness unit for elastomers). Recent advances have included an increase of the hardness of the rubber covering. On the other hand, new studies encourage the change of the conventional rubber covering by introducing a double layer covering: an inner layer with low hardness and an outer layer with high hardness (in contact with the tissue paper sheet). The aim of this procedure is to make the outer layer (surface of the rubber roll) more flexible (Biagiotti ). Each type of rubber has its own characteristics and depending on these they can be chosen as they are better for temperature resistance, and/or chemical resistance, and/or abrasion resistance, and/or long service life. The rubber of the roll undergoes different stresses with the embossing process. If the rubber hardness value were determined during the embossing process, it would be altered due to the stresses caused both in terms of pressure and temperature. Thus, the performance of the rubber roll will influence the engraving of the embossing pattern and, consequently, the properties of the tissue paper and directly the final product (Huff and Bell ). As demonstrated in the study developed by Vieira et al. (c), where the evaluation of the impact by changing rubber hardness on the embossing operation was performed, it was found that the highest softness value was achieved for the double layer solution, with an inner layer of 48 Sh-A (upper layer) and an outer layer in contact with the tissue paper sheet of 60 Sh-A (bottom layer). The results of the work also highlight an increase in softness with increasing rubber hardness for the replication of conventional coverage. The loss of mechanical strength and greater bulk, on the other hand, became more accentuated for the micro pattern and for lower rubber hardness.

The dimensions and the finishing geometry of the embossing elements (lines or points) are a limitation of this process. For example, patterns with thin embossing elements cannot be engraved too deeply, as they are prone to tearing the tissue paper sheet. In contrast, to obtain a high-quality embossing pattern engraving, the tissue paper’s ability to stretch and adapt to the relief is equally important, which is also a physical limitation. Currently, there are no standardized finishing geometries and/or designs that objectively define the impact they will have on the final properties of the tissue papers/products (Pál et al. ). Khan () showed that the mechanical properties of the embossed product were affected both by the density of dots (number of dots/cm2) of the embossing pattern, as well as by the height of the dots and the angle that the dot makes with the base. Khan () concluded that there is a greater loss of mechanical properties for a higher density of dots, and a greater height of the dots, which consequently lead to a greater deformation of the tissue paper sheet. In contrast, a dot with a higher base angle (cylindrical dot geometry – 90° angle with the base) leads to a lower loss of mechanical properties because of less deformation of the tissue paper sheet. In addition to the work developed by Khan (), another study was carried out in this area by Vieira et al. (d). In this study, the authors showed that the finishing geometry of the line and dots (straight or round) of the embossing pattern has an impact on the mechanical properties and softness of the products. The finishing of the straight embossing elements showed a higher softness value when evaluated individually. When mounting the 2-ply prototype of the deco and micro patterns, with the same finishing, the greatest softness was obtained for the prototype with the round finishing geometry. Because the micro pattern is the one that impacts the most the structure of the paper, resulting in greater bulk, it is with this pattern that the lowest values of softness and mechanical strength are obtained. In contrast, within both relief patterns (deco and micro), the straight finishing geometry is the one with the greatest loss of mechanical strength. With this work, in terms of finishing geometry of the embossing elements of the two patterns, the round finishing also stands out, as it doubles the bulk value when compared to tissue paper before embossing.

A tissue paper sheet laminating process presupposes that at least in an engraving NIP of one of the patterns, at least two tissue paper sheets are combined and engraved. Thus, another factor that can influence the properties of tissue products in this section of converting is the stacking sequence of sheets in a finished multilayer product with an odd number of sheets. In the study developed by Vieira et al. (a), two different stacking sequences of a 5-ply toilet paper were analyzed (Fig. 8), as well as their impact on their final properties of the final consumer.

Fig. 8. The 5-ply toilet paper with the two stacking sequence configurations (Vieira et al. a)

Configuration 1 is composed of 3 sheets with deco embossing and 2 sheets with micro embossing, and configuration 2 is composed in reverse. It was found, when comparing with same 5-ply tissue paper without any embossing, that in configuration 1 the bulk and water absorption capacity increased 46% and 2%, respectively. While for configuration 2, bulk and water absorption capacity increased 40% and 17%, respectively. The mechanical properties decreased considerably due to the embossing process. However, configuration 1 was shown to have the lowest losses. Regarding softness, the stacking sequence also affected the results, where configuration 2 proved to be the softest and most pleasant to the touch product, with an overall handfeel value of 75.3 HF, and the product produced with configuration 1 presented rougher and less pleasant to the touch, with an overall handfeel value of 68.0 HF (Mendes et al. ). Thus, it can be concluded that the number of sheets that enter each embosser in the stacking sequence influences the final properties of the paper and thus can be adapted to meet the requirements.

Liquid absorption is an important property for many tissue products, whose main purpose being to clean/absorb liquids. Liquid absorption is generally divided into absorption capacity, absorption time, and absorption rate. The absorption capacity reflects the maximum amount of water that the paper can absorb, and it is expressed in gwater / gfiber, absorption time is the time, expressed in secs, to absorb the maximum capacity, while the absorption rate, expressed in gwater / gfiber × sec, measures how quickly the product absorbs this amount of water (Kullander ). In European and International trade, both water absorption time and water absorption capacity represent important parameters in the field of tissue paper product comparison (Tutuş et al. ). In the work developed by Vieira et al. (b), it was shown that the embossing operation significantly increases the thickness and bulk of tissue paper while it has no impact on the water absorption time. Regarding the water absorption capacity, the embossing operation proved to have a great impact. The greater increase in bulk achieved with the embossing operation resulted in greater water absorption capacity. Currently, the embossing operation is a common step in the tissue paper converting because it creates empty spaces between the sheets of paper, such that the absorption capacity of the paper increases. Thus, the absorption performance of an embossed multilayer paper is far superior to that of an embossed single-layer paper (Zhipeng et al. ).

The Finite Element Method (FEM) is a numerical technique used to perform finite element analysis of any given physical phenomenon. For example, the authors Khan () and Vieira et al. (a,b,c,d) used this tool to simulate structural behavior of their materials, and to validate and therefore corroborate the experimental obtained results. This tool proved to be useful, as it can allow simulating other studies with different parameters variations, providing approximate results to the real ones.

Within this section, tissue paper decoration also takes place. This decoration can be done by colored glue or by printing. Any of these techniques are coupled to the converting machine as an additional process to embossing/laminating and the result is shown in Fig. 9 (Star Label ; Galli ).

The most used printing process is flexography, which allows printing at high speed, being suitable for these types of products. In addition, it allows cost-effective, high-quality printing of mass-produced products (Star Label ). Ink is transferred to tissue paper from the Anilox roll and through cells etched onto the printing plate (Johnson ).

Fig. 9. Decorated tissue products: a) tissue napkin printing with aqueous flexographic ink, and b) tissue kitchen towel lamination with blue color glue

To print a porous paper, such as tissue paper, it will be necessary to employ more ink, as it penetrates the structure of the paper instead of staying on the surface inducing a more rigid structure. Consequently, it will negatively affect absorption, softness, and mechanical properties (Theohari et al. ). The lamination with the glue decoration technique implies the replacement of the traditional transparent glue by a colored one that will bind the sheets making up the final product by joining dots/lines (Galli ). This methodology has a lower impact on the properties of tissue papers than the printing technique. The greater or lesser impact of these decoration techniques on the tissue paper properties are related to the greater or lesser decorated area, for example, a larger decorated area implies a greater impact on the final properties.

Perforation

Perforation in tissue paper products is used for the purpose of facilitating the portioning of paper sheets. The main products in which this process is used are toilet paper, kitchen towels, and facial tissues (Ogg and Habel ; Schulz and Gracyalny ; Baggot et al. ; Pejic ).

In the converting machine, perforation takes place at high speed. A roll with several diagonally arranged blades is pressed against the tissue paper sheet, cutting it at the points of contact (Perini et al. ). Then, the called perforation line is created, in which there are bonding areas, uncut areas that prevent the sheet from separating prematurely, and holes with a predetermined cut distance. The distance between two perforation lines determines the length of the “sheet” to be detached by the end consumer (Ogg and Habel ; Baggot et al. ; Chih ). Figure 10 schematically presents these concepts.

The strength required in the perforation zone to ensure that the paper separates is called the perforation tensile strength. This must be optimized to fulfill both the easy detachment of the sheet by the consumer, and to withstand the high speed and tensions to which the converting machine is subjected (Schulz and Gracyalny ; Mukai and Shimizu ). Thus, it is extremely important for producers to control the puncture resistance through the evaluation of the puncture efficiency, which according to the ISO -1 () standard is defined as “…the difference between the tensile strengths of an unperforated and perforated material from the same sample divided by the tensile strength of an unperforated material…”.

Fig. 10. a) Perforation scheme with identification of the cut and the connection areas (Vieira et al. ); b) Schematic of a roll with identification of the perforation lines (Vieira et al. e)

From the work carried out by Vieira et al. (, e) related to tissue paper perforation, the optimization of perforation efficiency was reached for an industrial cutting distance of 5 mm. It was also evidenced in these studies that the dimensions of the perforation cuts have greater impact on the perforation efficiency than the fibrous composition and/or number of sheets that make up the tissue paper product. Furthermore, it has been determined that above a stress concentration factor in the perforation cuts of 0.11, the sheet separates outside the perforation line. Both results were corroborated by the simulation analysis of the finite element method (FEM).

LOG Rewinding

The production of tissue paper LOG’s is performed using a rewinder that is calibrated to wind a predetermined amount of paper (Kimari ; Pejic ). This process is mainly used in the production of toilet paper rolls or kitchen rolls. It starts with feeding cardboard tubes, also known as “colors”, to this section of the converting machine. Then, a predetermined amount of glue is applied to its surface to which the perforated sheet of paper will adhere. The paper sheet is then rolled up until the defined amount of paper is reached. This operation is completed by gluing the last sheet of paper, commonly called “flap closure” or “tail sealing” (Brown ; Perini et al. ; Galli ). Then, the complete LOG is unloaded from the rewinder to the LOG slitting section, and a new LOG starts the production process. Whenever a new cycle of tissue products begins, when this stage is reached, the first LOG’s must be discarded, as the sheet arrives at the rewinder without being properly tensioned (Brown ; Perini et al. ). As with the rewinding of the mother reels, the LOG’s also show winding problems that will manifest as defects. The most common defects are offset core, poor start, crushed core, and a flap without glue or other sealant (Brown ; Pejic ).

Rewound coreless products

Most rolled products comprise a tubular core made of a more rigid paperboard material, which allows it to be placed in a holder which is inserted through the hollow for ease of consumption. After the product is consumed, the tubular core is discarded and can be sent for recycling; otherwise it is traduced into waste with an expected environmental impact (Maddaleni and Gelli ; Wojcik et al. ). When the coreless products appeared, the application of an adhesive was required. This was intended to stiffen the sheets near the center of the roll, to prevent deformation during use. This processing rendered the entire end of the roll unusable. Thus, it was also implied wasting a part of the product, which is not easy to recycle. Another disadvantage was the difficulty to place the roll in conventional supports, since the opening was small, non-existent, or non-circular. Nowadays, with the development of converting technology, coreless rolls are produced by spirally winding the tissue paper sheet, a process that defines a hollow passage through the center of the roll. This process makes unnecessary the usage of a tubular core and/or an adhesive that allows the inner layers to adhere to each other, and the entire product can be consumed reducing waste. However, in this type of processing the hydrogen bonds must be promoted by the introduction of moisture into the system. On the other hand, the key properties of these products remain unaltered, as they are not altered by contact with the adhesives and the roll core (Wojcik et al. ). Figure 11 shows two different ways of dispensing the product services from coreless rolls.

Fig. 11. Two ways of dispensing the product from coreless rolls

Fig. 12. Coreless toilet roll and the detachable toilet paper core

Another way to produce coreless roll consists of the creation of a first portion of tissue paper to form the inner core of the roll, and then a separator material (tissue paper obtained through a local variation in density or calendering) is applied at least in one turn around the outer of the pseudo-core. The remaining tissue paper is rolled around-up from the outside of this separation layer. This layer enables an easy extraction of the core from the roll, as can be seen in Fig. 12. These types of coreless rolls allow the end-user to use them in different supports. Tissue paper pseudo-core can also be used and transported in smaller spaces such as wallets or backpacks, that can also be used in their entirety with no waste (Maddaleni and Gelli ).

LOG Cut / Cutting

Now the complete LOG is transferred to the cutting section where the finished product rolls will be obtained with the required dimensions. The saws used for cutting the LOG’s are made of thin steel with a toothless blade (disc blades), and they can have a continuous or intermittent movement. Continuous motion saws can reach higher speed and are usually composed of several blades arranged side-by-side separated by the distance defined for the dimension of the finished product. In contrast, the intermittent motion saw applies the cut along the LOG that moves at intervals defined by the distance required for the dimension of the finished product (10 to 60 cm depending on the type of product) (Brown ; Kimari ; Pejic ; Guarini et al. ). Both types of saws are always placed perpendicular to the LOG (Brown ; Guarini et al. ).

This section of the converting machine includes at least one sharpening unit placed on the opposite side of the cut, which is composed by an abrasive material to be in contact with the cutting blade. The sharpening units come into operation as soon as the sensors detect the wear of the saw. Periodically the blades must be replaced as the wear and sharpening of the blade progressively decreases both the diameter of the blade and its cutting capacity (Guarini et al. ).

The most common problems that can be found due to LOG cutting blades are crushed core caused by increased axial eccentricity and blade distortion due to cutting speed limitation, ragged edges caused by an unadjusted blade life, and consequently stoppages for successive blade changes, bias cut caused by poor blade orientation in relation to the LOG (Ahuja et al. ), and dirty rolls of dust caused by the maintenance of LOG’s saws (Pejic ).

When cutting tissue paper for folding, the saws are presented as those of continuous movement for the LOG’s, in which they are arranged side-by-side and separated by the distance defined for the dimension of the finished product, as schematically represented in Fig. 4.

Folding

Folding is a typical converting operation for hand towels, facial tissues, napkins, and folded toilet paper. There are two types of converting machines that produce folded tissue paper products: those that fold the paper sheets with vacuum, and those that fold the paper sheets through a folding head composed by a pair of rotating steel cylinders with folding clamps, called the inter-folders. To produce premium products, it is necessary to guarantee a good bending quality as well as a good alignment of the sheets (Yasui ).

Regarding the folding itself, there are several types. The most common types of folds are represented in Fig. 13.

Fig. 13. Schematic representation of the main types of tissue paper folds

The most traditional form of folding is the C-fold. This type of folding is used in low quality products, but it creates an additional difficulty in its usage, making the end consumer take several sheets at the same time, which is more than essential. Then, there is the V-fold, also known as the Zig Zag fold, which is also used in low quality products. With this style of folding, the user can already have a greater control over its use, as it dispenses one sheet at a time. The V-fold type of folding is commonly used in facial tissue products. The most used fold for premium products is the Z-fold. This type of fold provides controlled use by the user, with one sheet at a time being dispensed. The sheets feature a clean cut and open automatically. Finally, there is the quarter fold (or ¼ Fold), which is the main fold used in napkins. This type of fold does not require a dispenser for its use (Galli ; Pearroc Ltd. ).

Regarding the product marketing, the type of folding can also be used as a way for the producer and the consumer to distinguish the quality of the product and perceive its respective final properties.

Packaging / Boxing

Generally, in converting machines, the packaging section is closed, and production is performed at high speed, and so it is important to have means of detecting the problems that occur in the packaging sequence to solve them as quickly as possible to guarantee improved quality of the products (Rempel ). It is rare that the packaging process damages the integrity of rolls/stacks of tissue paper, affecting their properties, but sometimes deformation can occur during bagging (Pejic ).

Generally, rolled products are vertically stacked with the core, while folded products (without core) are placed inside cardboard boxes. This is because during the storage of the pallets, they are often superimposed, so the lower pallet needs sufficient strength to support the upper pallet, thus jeopardizing the integrity of the products. Thus, for products with a core, the strength is provided by the core itself, and for products without a core, the strength is provided by the cardboard box in which the products are packed (Galli ).

Rewound products

The tissue paper rolls then arrive at the packaging section. Because of the high number of packaging configurations used for roll tissue products (from single roll packages to multi-packs up to 90 rolls), it is challenging for converting machines to comply with these configuration changes smoothly. In contrast, it is equally challenging for this type of machine to be adaptable to the material used for packaging, as it is increasingly necessary to consider the sustainability of the materials used (Alberti ).

In this section, the rolls are grouped according to the amount predetermined by the machine operator, and then wrapped in a paper sheet for packaging (which can be closed with glue) or in a plastic, which is usually done with polyethylene or bioriented polypropylene (whose packaging is closed using hot air) (Brown ; Pejic ). Depending on the model of the converting machine, the rolls can be packed in several layers. Each set of rolls that form a layer is lifted and placed on the bottom layer, and so on, until achieving the number of layers predetermined. Then, they are all packed together or bagged (Michelini ). Next, these packages can be placed directly stacked on pallets or first in cardboard boxes, and then on pallets to be stored in the finished product warehouse (Brown ; Pejic ).

Folded products

After the embossing, cutting and folding process, the stacks of folded paper are sent to the packaging section. These tissue paper stacks, depending on their final application, can undergo various types of packaging. For example, the napkins are packed in a plastic film in predetermined amounts, and then the napkin packs are packed in a cardboard box. Hand towels, contrastingly, are wrapped in a paper or plastic film and then stacked inside a cardboard box. The packs of facial tissues, with about 8 to 10 tissues per pack, are packed in a plastic film, which will be perforated, and a self-adhesive label will be glued (creating the opening and closing of the pack), then a predefined group of these packs is placed in a bag and later in a cardboard box for later dispatch (Michelini ).

Palletizing

Now that the products are packed, they go to the palletizing section. The main problem that can exist in this section is the fact that the suction cups/robot arms can deform the packages, damaging the product contained therein. In addition to the bad appearance caused in the packaging, this results in a problem for the palletization itself, as deformed packaging takes up more space, reducing the efficiency of packaging stacking. It can also increase the amount of plastic wrap used to close the pallet (Reynolds ).

Conversely, there are deformations that can be purposeful. In Brazil, a considerable portion of the population goes to the supermarket by public transport or on foot, traveling long distances, and therefore transporting toilet paper is challenging. Additionally, the apartments are very small, and the toilet paper takes up a lot of space. Thus, the packing of a set of rolls with the packaging film will compress them, and this will considerably reduce their size, solving the transportation problem. This packaging method of reducing the size of roll packaging by compression is called Just One Hug (Kim and Mauborgne ). With the reduction in packaging, the efficiency of palletization is also improved, as a greater number of rolls per pallet can be transported, as shown in Fig. 14.

In Brazil, cargo is transported mainly by road, and thus, being able to transport more rolls per pallet caused a decrease in transport costs. With the Just One Hug packaging method, there was a drop of approximately 15% in transport costs and 19% in the amount of packaging material used, thus reducing the price for the consumer, in addition to satisfying the packaging dimensions reduction requirements, without reducing the amount of product. As this compression impacts the properties of the finished product, such as bulk and softness, this packaging method was combined with products composed by recycled fibers (lower quality products) (Kim and Mauborgne ).

Fig. 14. Schematic representation of rolls packages palletization with and without compression

Dusting & Linting

Tissue paper products, in general, can release extremely high concentrations of dust (fibers with a length approximately 0.4 to 2.0 mm) and lint (fibers with a length approximately 4.0 to 5.0 mm and a width of 500 μm), which are encountered during stages of processing and packaging (Baum ; Frazier et al. ). In the manufacturing process of this type of product, these fibers and dust accumulate on the surface of the paper and in the elements of the converting machines, which translates into product quality problems and difficulties in runnability, and later, in the usage of the final consumer (Kuryllowicz ; Linder et al. ).

Fig. 15. Major contributing factors to dust and lint generation in tissue converting

This lint and dust accumulation form agglomerates on the surface of the tissue paper sheet, and consequently decreases its softness with a roughness increase. Due to this fact, the usage of these products contaminated by lint and dust becomes unpleasant, such that the product does not meet the requirements of the final consumer (Frazier et al. ). The fishbone diagram presented in Fig. 15 shows the major contributing factors to dust and lint generation in tissue converting (Frazier et al. ).

FINAL CONSIDERATIONS

It is in the converting machine where value is added to tissue paper products, which is why these machines are constantly evolving. At the beginning of the tissue paper transformation, the paper was rewound by hand on a mandrel, and when the first semi-automatic machine appeared, it was wound at a few LOG’s per minute. Currently, product design plays an important role, as in addition to its apparent sophistication, it is the key to optimizing its properties. Therefore, increasingly more products are engraved and printed, and design patterns are constantly changing and optimizing. These machines have become sophisticated and uninterrupted, being able to be computer-controlled and quickly programmed to produce the desired product. The fact that the automation of the converting machines goes all the way to the end of the line (palletization), allows the producer to have better control of the quality and price of the product presented to the consumer. As a result, the products that reflect the needs and desires of customers have an improved chance of success for the producer. The competitive advantage will be found by producers who use the latest technology, because with the actual slowdown in the economy, products will have to be redesigned to find a lower price, which means making an additional effort to produce the products at the lowest possible price cost as well as lowering the cost of transportation through distribution channels. Thus, the digital twining of the several converting processes provides a modeling tool, which allows optimization in a digital environment, without having to undergo several trial-and-error cycles to determine the optimal parameters of the processes (Spirent ). According to recent publications, the simulations were carried out on a macroscopic scale considering an orthotropic homogeneous fiber distribution in a quasi-static loading. An improvement of the simulations will be made by taking into account a microscopic characterization of the fiber’s distribution and orientation. This information is then used to represent in a mesoscale considering representative elementary volumes, and finally replicating them into space to achieve the macroscale mechanical behaviors, and also considering a dynamic loading using time-dependent constitutive models.

Because of the high competition and secrecy between different tissue paper producers and suppliers, there are few studies and publications related to the production, and its impact on the final properties of these types of tissue paper products, as already observed by other authors (Assis et al. ). This review article has shown that some progress has been made and that most of the findings referenced here are recent, which indicates a slight opening of the industry in creating partnerships to deepen these mechanical impacts on the properties of the finished products. Figure 16 summarizes in a fishbone diagram the impact of the converting operations on the final properties of the finished tissue products.

Fig. 16. Impact of the converting operations on the final properties of the tissue products

FUTURE DIRECTIONS

Within the converting operations, embossing has a major impact on the quality of tissue products. Therefore, in the near future, it deserves special attention in new and innovative research and development methodologies to follow-up the digital transition and fulfill the exigent consumer requirements.
The natural evolution of the embossing process tends to go in the direction of changing the conventional rubber covering by the introduction of a double layer covering with an inner layer with low hardness and an outer layer with high hardness rubbers.
The final quality of the tissue products is mostly related to the patterns and the corresponding finishing geometries of the embossing. It is a challenge to be able to integrate the design of the embossing patterns, the respective type of finish geometry, and the density of the marked area in an automatic procedure that allows to predict the final properties and quality of the final tissue product.
Due to the market demands, the adaptability of converting machines, and their rapid updating, is imperative for the producer since the response to consumer requirements is their main motivation.
The digital twining of several converting processes is an emerging simulation tool that will be a trend in the near future. It will enable optimization in a digital environment transition.

ACKNOWLEDGMENTS

The authors gratefully acknowledge the funding of this work that was carried out under the Project InPaCTus – Innovative Products and Technologies from Eucalyptus (Project Nº ) funded by Portugal through the European Regional Development Fund (ERDF) in the frame of COMPETE nº246/AXIS II/.

The authors are also very grateful for the support given by research unit Fiber Materials and Environmental Technologies (FibEnTech-UBI), on the extent of the project reference UIDB//, and by the Center for Mechanical and Aerospace Science and Technologies (C-MAST-UBI), on the extent of the project reference UIDB//, both funded by the Fundação para a Ciência e a Tecnologia, IP/MCTES through national funds (PIDDAC).

REFERENCES CITED

A.Celli Group (). “How to maintain the softness and bulkiness of tissue during rewinding,” Papnews, (https://www.papnews.com/insight/how-to-maintain-the-softness-and-bulkiness-of-tissue-during-rewinding-thanks-to-a-celli-solutions/), Accessed 23 June .

Ahuja, R., Graham, D., and Isaacs, T. (). Surface Engineered Log Saws for Enhanced Tissue Conversion Productivity & Quality, International Knife and Saw, Florence, SC, USA.

Alberti, G. (). “Primary packaging: Challenges — and solutions — for tissue converters,” Koerber Tissue, (https://blog.koerber-tissue.com/primary-packaging-challenges-and-solutions-for-tissue-converters), Accessed 23 June .

de Assis, T., Reisinger, L., Pal, L., Pawlak, J., Jameel, H., and Gonzalez, R. (). “Understand the effect of machine technology and cellulosic fibers on tissue properties – A review,” BioResources 13(2), –. DOI: 10./biores.13.2.DeAssis

Baggot, J., Gropp, R. F., and Wojcik, S. (). “System and method for severing or perforating a web,” US Patent No. /.

Baum, S. (). “Web cleaning method,” US Patent No. B1.

Biagiotti, M. (). “Tissue embossing developments – The tissue story,” (https://www.tissuestory.com//11/21/tissue-embossing-developments/), Accessed 08 Jan .

Brown, S. R. (). “Overview of tissue finishing and converting,” TAPPI Journal 74(10), 91-94.

Chih, C.-K. (). “Perforation design & calculation of toilet paper rewinder,” China Pulp and Paper 37(9), 38-42. DOI: 10./j.issn.-508X..09.007

Cigolini, R., and Rossi, T. (). “Improving productivity of automated tissue converting lines: An empirical model and a case study,” Production Planning & Control 15(5), 550-563. DOI: 10./

DeMaio, A., and Patterson, T. (). “Similarities in bonding influence between pre-failure tensile creep and stress–strain behavior of paper,” Mechanics of Materials 40(3), 133-149. DOI: 10./j.mechmat..06.007

Digby, P. (). “pd-Tissues – Trees to paper,” pd- Tissues, (http://pd-tissues.co.uk/trees-to-paper.aspx), Accessed 13 Feb .

D’Olivo, I. (). “Problems in tissue rewinding: How to solve them with our A.Celli E-WIND® T100 Rewinder,” A.Celli, (https://www.acelli.it/en/blog/problems-tissue-rewinding-e-wind-t100-rewinder), Accessed 20 Apr .

Frazier, R., Zambrano, F., Pawlak, J. J., Peszlen, I., Welsford, D., and Gonzalez, R. (). “The tissue dust analysis system: A new device and methodology to quantify dusting and linting propensity in hygiene tissue papers,” Cellulose 29(15), -. DOI: 10./s-022--0

Galli, E. (). “Module 4 – Tissue paper production process and properties,” Tecnicelpa Course – Introduction to the paper production process, University of Beira Interior, Covilhã, Portugal.

Giannini, D. (). “Resistance: Part IV,” Körber LinkedIn, (https://www.linkedin.com/pulse/resistance-part-iv-dario-giannini/>), Accessed 08 Sep .

Guarini, C., Betti, G., Catalini, A., and Giurlani, G. (). “Cutting machine for paper material LOGs with a sharpening unit,” US Patent No. US .

Huff, S., and Bell, J. (). “How Do You Know YouTMve Got the Right Cover for Your,” in: AIMCAL Fall Technical Conference and 19th International Vacuum Web Coating Conference , Myrtle Beach, SC, USA, pp. 1-8.

ISO -1 (). “Tissue paper and tissue products – Part 1: Vocabulary,” International Organization for Standardization, Geneva, Switzerland.

Janda, B. (). “Sheet structure process effect on tissue properties,” TAPPI TISSUE 360o, (https://tissue360.tappi.org//12/28/sheet-structure-process-effect-on-tissue-properties/), Accessed 13 Dec 13 .

Johnson, J. (). Aspects of Flexographic Print Quality and Relationship to Some Printing Parameters, Faculty of Technology and Science, Chemical Engineering, Karlstads Universitet, Karlstad, Sweden.

Khan, A. A. (). Development of Model to Simulate Embossing of Tissue Paper – Effect of Embossing on Mechanical Performance of Tissue, Master’s Thesis, KTH Royal Institute of Technology, Stockholm, Sweden.

Kim, C., and Mauborgne, R. (). “How a consumer-goods giant made its toilet paper stand apart,” Blue Ocean Strategy, (https://www.blueoceanstrategy.com/blog/how-a-consumer-goods-giant-made-its-toilet-paper-stand-apart/), Accessed 28 June .

Kimari, O. (). Papermaking Science and Technology: 18 – Paper and Board Grades, by H. Paulapuro, J. Gullichsen, and H. Paulapuro (eds.), Suomen Paperi-Insinöörien Yhdistys and Technical Association of the Pulp and Paper Industry, Fapet Oy, Helsinki, Finland.

Kullander, J. (). Evaluation of Furnishes for Tissue Manufacturing, Licentiate Thesis, Karlstads Universitet, Karlstad, Sweden.

Kuryllowicz, K. (). “Dust extraction system improves working conditions” [at E. B. Eddy Forest Products Ltd.’s Mill in Quebec]. Pulp Pap. J. 37, 32.

Lamberg, J. A., Ojala, J., Peltoniemi, M., and Särkkä, T. (). The Evolution of Global Paper Industry –, World Forests, Springer, Dordrecht, Netherlands. DOI: 10./978-94-007--7

Linder, R., Furman, G., Lowe, R., Castro, D., Melchiors, R. (). “Tissue dust reduction,” WO Patent No. / A1.

Maddaleni, R., and Gelli, M. (). “Coreless roll of web material, machine and method for its production,” US Patent No. B2.

Mendes, A. de O., Vieira, J. C., Carta, A. M., Galli, E., Simões, R., and Fiadeiro, P. T. (). “Influence of tissue paper converting conditions on finished product softness,” BioResources 15(3), -. DOI: 10./biores.15.3.-

Michelini Tissue Consulting (). “Tissue converting,” Tissue Easy, (https://www.tissueasy.com/_tissue-converting.php), Accessed 21 June .

Mukai, T., and Shimizu, Y. (). “Toilet paper roll with perforated line,” Japan Patent No. JPA.

Ogg, R. G., and Habel, M. A. (). “Perforator blade for paper products and products made therefrom,” U.S. Patent No. .

Pál, M., Banjanin, B., Dedijer, S., Vladić, G., and Bošnjaković, G. (). “Preliminary analysis of image processing-based evaluation of embossing quality,” in: Proceedings – The Tenth International Symposium GRID , Novi Sad, Serbia, pp. 269-279. DOI: 10./GRID--p29

Paolinelli, A., Boschi, L., and Ricci, M. (). “Unwinder for reels and unwinding method,” U.S. Patent No. .

Pearroc Ltd. (). “Types of hand towel folds,” (https://www.pearroc.com/paper/hand-towels-z-fold-interfold-cfold/products/types-of-hand-towel-folds), Accessed 21 June .

Pejic, D. (). Identifying and Reducing Converting Paper Waste – A Case Study at SCA’s Paper Mill in Lilla Edet., Master’s Thesis, Chalmers University of Technology, Gothenburg, Sweden.

Perini, F., Giurlani, G., and Pelaia, F. (). “Rewinder for the production of paper logs,” U.S. Patent No. .

Rempel, M. (). “Effectively solving tissue production, converting and packaging problems using event capturing camera systems,” Papnews, (https://www.papnews.com/insight/effectively-solving-tissue-production-converting-packaging-problems-using-event-capturing-camera-systems/), Accessed 23 June .

Reynolds, P. (). “Reliability comes to palletizing,” Packaging World, (https://www.packworld.com/machinery/secondary-end-of-line/article/ /reliability-comes-to-palletizing), Accessed 28 June .

Schulz, G., and Gracyalny, D. (). “Method and apparatus for pinch perforating multiply web material,” U.S. Patent No. .

Spina, R., and Cavalcante, B. (). “Characterizing materials and processes used on paper tissue converting lines,” Materials Today Communications 17, 427-437. DOI: 10./j.mtcomm..10.006

Spirent (). “Simplifying 5G with the network digital twin – White paper,” Spirent, (https://assets.ctfassets.net/wcxs9ap8i19s/3BEsXS0UL7Y97v8GxtMINJ/3aafaf5aab5b520bdf7/WP-Simplifying-5G_with-the-Network-Digital-Twin.pdf), Accessed 07 July .

Star Label (). “Flexography 101: The basics of the flexographic printing process,” Star Label Products, (https://www.starlabel.com/blog/flexography/), Accessed 06 Sept .

Theohari, S., Fraggedakis, E., Tsimis, D., Tsigonias, M., and Mandis, D. (). “Effect of paper properties on print quality by flexographic method,” in: 46th Annual International Conference on Graphic Arts and Media Technology, Management and Education, Athens, Greece, pp. 1-10.

Tutuş, A., Çiçekler, M., and Çali, A. (). “Tissue papers in Turkey and some physical and optical properties,” SDÜ Fen Bilimleri Enstitüsü Dergisi 20(1), article no. . DOI: 10./sdufbed.

Vieira, J. C., Mendes, A. de O., Carta, A. M., Fiadeiro, P. T., and Costa, A. P. (a). “Impact of 5-ply toilet paper configuration on its mechanical and absorption properties,” BioResources 15(4), -. DOI: 10./biores.15.4.-

Vieira, J. C., Mendes, A. de O., Carta, A. M., Galli, E., Fiadeiro, P. T., and Costa, A. P. (b). “Impact of embossing on liquid absorption of toilet tissue papers,” BioResources 15(2), -. DOI: 10./biores.15.2.-

Vieira, J. C., Mendes, A. de O., Ribeiro, M. L., Vieira, A. C., Carta, A. M., Fiadeiro, P. T., and Costa, A. P. (a). “Embossing pressure effect on mechanical and softness properties of industrial base tissue papers with finite element method validation,” Materials 15(12), article no. . DOI: 10./ma

Vieira, J. C., Mendes, A. de O., Ribeiro, M. L., Vieira, A. C., Carta, A. M., Fiadeiro, P. T., and Costa, A. P. (b). “FEM analysis validation of rubber hardness impact on mechanical and softness properties of embossed industrial base tissue papers,” Polymers 14(12), article no. . DOI: 10./polym

Vieira, J. C., Mendes, A. de O., Ribeiro, M. L., Vieira, A. C., Carta, A. M., Fiadeiro, P. T., and Costa, A. P. (c). “Embossing lines and dots geometry effect on the key tissue paper properties with finite element method analysis,” Polymers 14(17), article no. . DOI: 10./polym

Vieira, J. C., Morais, F., de Oliveira Mendes, A., Ribeiro, M. L., Carta, A. M., Curto, J., Amaral, M. E., Fiadeiro, P. T., and Costa, A. P. (d). “Mechanical and softness characterization of ‘deco’ and ‘micro’ embossed tissue papers using finite element model (FEM) validation,” Cellulose 29, -. DOI: 10./s-022--2

Vieira, J. C., Vieira, A. C., Mendes, A. de O., Carta, A. M., Fiadeiro, P. T., and Costa, A. P. (). “Mechanical behavior of toilet paper perforation,” BioResources 16(3), -. DOI: 10./biores.16.3.-

Vieira, J. C., Vieira, A. C., Mendes, A. de O., Carta, A. M., Fiadeiro, P. T., and Costa, A. P. (e). “Toilet paper perforation efficiency,” BioResources 17(1), 492-503. DOI: 10./biores.17.1.492-503

Williams, B. (). “Roll winding defects – A brief troubleshooting guide,” Montalvo Corporation, (https://www.montalvo.com/article-library/roll-winding-defects-troubleshooting-guide/), Accessed 20 Apr .

Wojcik, S. J., Verburgt, M. R., Banda, J., Pigsley, K. A., Armstrong, C. A., Jobs, D. M., Shannon, T. G., and Baggot, J. L. (). “Coreless tissue rolls and method of making the same,” US Patent No. B2.

Yasui, S. (). “Manufacturing method for tissue-paper product,” Japan and World Patent No. WO A1.

Zhipeng, Z., Kuibin, D., Chenxi, L., Xingye, A., Haibing, C., Bin, L., and Hongbin, L. (). “Factors affecting the absorption performance of tissue paper,” China Pulp and Paper 41(6), 89-94. DOI: 10./j.issn.-508X..06.014

Article submitted: September 16, ; Peer review completed: October 22, ; Revised version received and accepted: December 7, ; Published: December 12, .

DOI: 10./biores.18.1.Vieira

Understanding the effect of machine technology and cellulosic fibers ...

de Assis, T., Reisinger, L. W., Pal, L., Pawlak, J., Jameel, H., and Gonzalez, R. W. (). "Understanding the effect of machine technology and cellulosic fibers on tissue properties – A Review," BioRes. 13(2), -.

Abstract

Hygiene tissue paper properties are a function of fiber type, chemical additives, and machine technology. This review presents a comprehensive and systematic discussion about the effects of the type of fiber and machine technology on tissue properties. Advanced technologies, such as through-air drying, produce tissue with high bulk, softness, and absorbency. Conventional technologies, where wet pressing is used to partially dewater the paper web, produces tissue with higher density, lower absorbency, and softness. Different fiber types coming from various pulping and recycling processes are used for tissue manufacturing. Softwoods are mainly used as a source of reinforcement, while hardwoods provide softness and a velvet type surface feel. Non-wood biomass may have properties similar to hardwoods and/or softwoods, depending on the species. Mechanical pulps having stiffer fibers result in bulkier papers. Chemical pulps have flexible fibers resulting in better bonding ability and softness. Virgin fibers are more flexible and produce stronger and softer tissue. Recycled fibers are stiffer with lower bonding ability, yielding products that are weaker and less soft. Mild mechanical refining is used to improve limitations found in recycled fibers and to develop properties in virgin fibers. At the same time that refining increases strength, it also decreases bulk and water absorbency.

Download PDF

Full Article

Understanding the Effect of Machine Technology and Cellulosic Fibers on Tissue Properties – A Review

Tiago De Assis,a Lee W. Reisinger,b Lokendra Pal,a Joel Pawlak,aHasan Jameel,a and Ronalds W. Gonzalez a,*

Keywords: Tissue paper properties; Softness; Water absorbency; Wet strength; Dry strength; Tissue machine technology; Cellulosic fibers; Mechanical refining

Contact Information: a: Department of Forest Biomaterials Science and Engineering, Box , North Carolina State University, Raleigh, NC -, USA; b: ReiTech Incorporated, 26 The Point, Coronado, CA, , USA; *Corresponding Author:

INTRODUCTION

Hygiene tissue paper products are manufactured to meet the desired performance according to a specific application inside a market segment. Overall, water absorbency, softness, strength (dry or wet), and disintegration are the most important properties used to evaluate the performance of tissue products. The observed properties of commercial tissue products are basically a function of fibers, chemistry, and manufacturing technology. There is a vast number of fiber types, tissue machine technologies, and chemical additives available in market for manufacturing of tissue products. Inside this complex environment, tissue paper manufacturers have to choose the right combination of fibers, additives, and technologies to produce specific tissue products capable of achieving the desired performance while providing enough profitability to the producer. Motivated by the complexity of this task, the main objective of this review is to present a discussion about how tissue paper properties can be tuned as a function of fiber type and tissue machine technology. This review brings a comprehensive description about a) tissue products, grades, and their properties, b) a comparison of product performance from different tissue machine technologies, c) properties of different type of fibers, and d) the effect of mechanical refining on tissue properties. Even though chemical additives (e.g. softeners, surfactants, strength additives) are commonly used in tissue manufacturing to improve tissue properties, this article will not cover this topic. Information about the use of chemical additives in tissue manufacturing can be found elsewhere (Neal ; Forbess ).

Tissue Paper Definitions, Products, Market and Grades

Based on their function, paper products can be placed in three main categories: i) packaging – defined as packaging materials, ii) printing and writing – defined as graphic papers, and iii) wiping and absorbing – defined as household and sanitary papers. Products in the third category, also known as tissue and hygienic papers, have a wide range of types and applications, including facial tissue, toilet tissue, napkin, kitchen towel, hand towel, and wipes. Some tissue papers are also used in the manufacturing of baby napkins and sanitary towels (Hubbe ; Kilby and Crevecoeur ; FAO a). Nowadays, tissue paper, together with packaging products, are the most promising sectors in the paper industry due to the constant increase in demand. The global production of tissue paper has been in constant growth for the past ten years (average annual growth rate is 2.6%), reaching a global production of 32.8 M tonnes with a total market value of $ 72.8 billion in (Euromonitor ; FAO b).

This diverse assortment of tissue products is commercialized in two market segments: i) Away From Home (AFH), professional or institutional segment; ii) At Home (AH), domestic or consumer tissue segment (Tprint ). AFH products are designed and sold for non-domestic consumption. Consumers typically use those products in workplaces, catering services, and public places (e.g.offices, industries, restaurants, arenas, hotels, malls, parks) (Wrap ). The customers of AFH products are institutions that buy tissue products from manufacturers or resellers and decide what products they want to buy to satisfy their customer’s (consumer) needs. Therefore, the consumption of those products, from the final consumer perspective, comes as a secondary need. In other words, if consumers want to go out to have a nice dinner, it is more likely that they would prefer to go to a restaurant that offers their favorite food than going to a place with premium napkins. On the other hand, AH products are designed for domestic consumption and are usually found at wholesalers or retailers. The consumption of those products come as the primary need for consumers. In this case, consumers will decide about what tissue product to buy based on the desired performance and price. For example, if consumers prefer to use very soft, white, and strong bath tissue, it is more likely that they would prefer to buy a premium product than a basic bath tissue, even though they would have to spend more money to satisfy their needs.

Tissue products are manufactured and sold in a variety of brands that can be divided into two major groups: a) National Brands (NB) and b) Private Label Brands (PLB). NB are brands owned by the manufacturers and PLB are brands owned by wholesalers or retailers. After its appearance more than a century ago, PLB became very popular among retailers and consumers (Hyman et al. ). In , the PLB market share in the tissue market was approximately 27% in the USA (with a growth of 9% over the last ten years in the USA) and 67% in Western Europe (Pöyry ). With the commercialization of PLB products, retailers have the potential to increase their overall profits. PLB products are typically purchased by retailers at prices slightly above the marginal costs (8% to 10% margin), and usually retailers spend much less on research and development, product launching, selling and advertising. As a result, by commercializing PLB products, retailers would have higher gross margin and higher bargaining power when compared to NB products. Additionally, PLB products contribute to building retailer’s chain image and boosting customers’ loyalty, especially when PLB products have constant and good quality. Manufacturers can also benefit with the production of PLB products. PLB production has the potential to reduce manufacturer’s unit fixed costs via economy of scale when NB and PLB are produced together. Additionally, PLB production will reduce the participation of competitors in the market place and will increase cooperation with retailers. However, PLB production can result in losses to manufacturers due to insufficient profit and cannibalization of their own NB products. Usually, non-leading NB manufacturers benefit the most with PLB production. Typically, PLB consumers are price-sensitive and value-oriented, willing to pay less in a given product category. On the other hand, consumers that are more influenced by advertising and are less price-sensitive, relying on unquantifiable experience attributes, tend to choose NB products (Hyman et al. ).

Table 1. Matrix of Fiber Types and Technology Used to Make a Range of AFH Tissue Products and Grades in the European Market (adapted from Wrap )

As a function of fiber properties, chemistry, process conditions, and technology, tissue products can be classified in three major grades or categories: a) Economy and Value products (EV); b) Premium products (PR), and c) Ultra products (UL). EV products are the most affordable products, capable of meeting minimum performance requirements. Those products have one or two plies and are manufactured with conventional technology, such as wet-creped and dry-creped technologies. EV products have high content of recycled and low quality fibers (such as mixed office waste, old corrugated containerboard). PR products can also be manufactured with conventional technology. However, they usually have a lower content of recycled fibers when compared to EV products. UL category accounts for more expensive and high-performance products, manufactured with a minimum amount of recycled fibers. UL products are usually manufactured combining advanced technologies, such as through-air drying (TAD), high content of virgin and high-quality fibers, multiple plies (2 or 3), and chemicals (softeners, debonders, wetting agents) (Fisher ; Zou ).

Table 1 presents a matrix that illustrates the type of fiber and technology used to manufacture AFH products in the European market. The likely content of recycled fibers in AFH products may range from up to 100% to as low as 20% as product category moves from EV products (manufactured with conventional technology) to UL products (manufactured using advanced technology). As a result of type of fiber and technology, the final properties of tissue products improve as one goes from the left to the right side of the matrix. For example, the combination of proper virgin fibers and advanced technology would result in a high bulk and soft tissue product with good absorbency. On the other hand, the use of the high content of recycled fibers and conventional technology would result in a denser tissue paper with lower softness and lower absorbency (Wrap ).

TISSUE PAPER PROPERTIES

Tissue properties are much more influenced by consumer desires than by manufacturing needs (Novotny ). Every tissue product is designed for a specific application and performance, which will determine their primary, essential or functional properties. For example, kitchen towels are mainly used for cleaning and absorption purposes (Council of Europe ). When consumers use a kitchen towel, they usually expect to have a strong product, especially under wet conditions, capable of cleaning a dirty wet surface without breaking apart. Another important property for kitchen towels is absorbency. Consumers expect that kitchen towels would be capable of absorbing and holding as much water as possible when they have to dry a wet surface. Therefore, wet strength and absorbency could be considered as the primary, essential or functional properties of kitchen towel products (Kim et al. ; Loebker and Sheehan ; Kan and Wong ). Other properties, such as softness, brightness, and appearance could be considered as secondary properties because those usually do not have a significant contribution to the main purpose of kitchen towels (cleaning and drying surfaces). However, it is important to highlight that the distinction between primary and secondary properties is based on the functionality of the products and it is not based on particular needs of a different group of consumers in different market segments and geographic regions. For example, softness has become an important property for the marketing of kitchen towels. Even though a soft towel will not help to dry a wet surface better, consumers that are sensitive to softness would still seek for such products to satisfy their needs of experiencing a better hand feel comfort (Kim et al. ; Kan and Wong ).

According to Zou (a), target properties for tissue products in the American market change among different applications. Softness and strength are desirable for bath tissue, while absorbency is also important for facial tissue. For napkins, strength and absorbency are target properties, while bulk is also important for towels. According to Novotny (), softness, absorbency, and brightness are very important for bath and facial tissue, while absorbency and strength are more essential for towel and napkin. Table 2 presents the suggested primary properties of some AFH tissue products in the European market and Table 3 presents a benchmark comparison among all the national brands of kitchen towels in the USA market.

Table 2. Summary of Primary or Essential Properties of AFH Tissue Products in the European Market (Adapted from Wrap )

Table 3. Summary of Machine Technology and Properties for All National Brands of Kitchen Towels in the USA Market (Adapted from Gonzalez et al. )

1 Basis Weight (TAPPI T 410)

2 Bulk (TAPPI T 411)

3 Wet Tensile Energy Absorption (ISO -4)

4 Water Absorbency Capacity (ISO -8)

5 Softness (Tissue Softness Analyzer): real softness measured with Tissue Softness Analyzer – EMTEC. The lower the value, the softer is the sample.

6 CTAD: Creped Through-Air Drying (Advanced technology)

7 DRC: Double Re-Crepe (Advanced technology)

8 UCTAD: Un-Creped Through-Air Drying (Advanced technology)

9 LDC: Light Dry-Crepe (Conventional technology)

Bulk

Bulk is defined as the volume occupied by a given weight of paper. It is the inverse of apparent density and can be correlated with many other mechanical properties of paper (Thorp ). Bulk is an important property for tissue products because paper thickness and bulk correlates well with absorbency and bulk softness (Novotny ). Compaction of the fiber network is an unwanted effect if the target is to produce a very bulky product. A higher bulk can be achieved when tissue product is manufactured with advanced technologies (e.g., TAD process), where wet pressing of the paper web is minimized. Other process conditions, such as the use of lower pressure in the press nips, milder refining of fibers, and paper creping will also contribute to higher bulk (Kullander ). Besides technology, fiber type also plays an important role in tissue bulk. Cellulosic pulps, such as eucalyptus and southern hardwood, produced from species having high Runkel ratio (2 x cell wall thickness / lumen diameter) are more rigid and less prone to collapse, resulting in a thicker and bulkier paper product. Additionally, high yield pulps can also be used to produce a higher bulk tissue product. High yield pulps are less flexible than low yield pulps due to their higher content of lignin and lower porosity, resulting in a more rigid structure (Nanko et al. ). Recycled bleached kraft fibers, with a history of drying, tend to be stiffer and less conformable, which will result in a higher bulk paper product that is desirable for tissue production. However, many recycled fibers already have been refined extensively, tending to produce a relatively dense sheet of paper (Hubbe ).

Absorbency

If you want to learn more, please visit our website Soontrue.

Absorbency is an important property for toweling and other tissue products with the purpose of wiping liquids. Absorbent tissue products should be capable of readily absorbing water (absorbency rate) and retaining a high level of absorptivity (absorbency capacity) until the end of the task (Kullander ). The ability to absorb liquid depends on having a high capillary pressure to suck the liquid and high permeability to allow the fluid to quickly flow away from the point of insult. The arrangement of hydrophilic fibers in a low density paper structure is responsible for the absorbent behavior of tissue products (Beuther et al. ). When paper products get in touch with water, the first phenomenon is surface wetting, followed by the penetration of water inside the paper structure. The penetration phenomenon is a very complex process because it will cause swelling of fibers as water is absorbed into fiber cell wall, resulting in changes in volume and pore structure of the paper (Thorp ). Absorbency properties are influenced by chemical properties of fiber surface and porosity of the paper web structure (Kullander ). Absorbent products have large amounts air-filled spaces among the fibers in the paper structure (Hubbe ). Absorbency can be controlled by fiber type, refining, creping, plies, and additives (Kullander ).

Fibers containing high content of lignin have lower water absorbency. For example, due to its high content of lignin, mechanical pulps can absorb about 1 gram of water per gram of pulp, while bleached fibers, such as kraft fibers, can typically absorb 5 to 10 grams of water per gram of fiber. Lignin removal increases hydrophilicity, porosity, and swellability of bleached kraft fibers, resulting in improved water uptake. The extractives present in cellulosic fibers also have a hydrophobic behavior. On the other hand, absorbency of cellulosic fibers is positively correlated with the content of hemicellulose (Hubbe et al. ). Tissue products manufactured with curly fibers are bulkier and more absorbent (Trepanier ). Bath tissue and towel products are made from lightly refined fibers to maintain initial relative stiff and tube-like nature of fibers that are necessary to achieve a high level of absorptivity (Thorp ; Hubbe ).

Typically, in a saturated tissue product, water is located in the spaces between plies, spaces between fibers, in the fiber lumen, and inside the cell wall. Within the cell wall, water can be located in micro, meso, and macropores. Water present in micropores is classified as non-freezing and freezing water. Non-freezing water corresponds to the first layers of water associated with the biomass surface. Freezing water corresponds to the water that has a depressed melting temperature due to the curved interfaces in micropores. The water present in macropores has similar thermodynamic properties to those of the bulk that is also present in the lumen, between fibers, and between plies (Kullander ). Most of the absorbed water is located in the spaces between fibers, and machine technology is an important variable to create inter-fiber spaces. TAD machines produce tissue products with higher bulk and higher absorbency than conventional machines. The number of plies also influences the absorbency, but to a lower degree when compared to the type of technology. The space between plies improves not only the absorbency capacity due to the creation of inter-ply water storage, but it also improves the absorbency rate. Lamellar flow channels are created between the plies, and such channels reduce the viscous flow resistance and improves absorbency rate. The absorbency capacity gained with the additional ply is usually greater than the capacity held within a single ply (Loebker and Sheehan ).

Strength

Tissue products are exposed to stresses and strains during the manufacturing of tissue jumbo rolls (e.g. paper machine, creping, winding), conversion of the jumbo rolls into the consumer size products (e.g. unwinding, embossing, perforation, rewinding, log sawing) (Brown ), and final use by the consumers (e.g.pulling, tearing, scrubbing, drying). Under those conditions, tissue has to be designed to develop strength properties necessary to meet stresses and strains requirements during manufacturing and while used by consumers.

Basically, the strength of paper is a function of three factors: i) strength and arrangement of fibers in the tissue web; ii) level of molecular bonding among fibers; iii) presence of strength additives. The first two factors are affected by processes variables and feedstock type. Chemical processes, such as bleaching, can reduce fiber strength, while refining and wet pressing usually improve bonding between fibers (Thorp ). Tissue products manufactured in tissue machines where pressing is used to partially dewater the tissue web (e.g. dry-creped) are stronger than tissue products produced in a TAD machine where minimal pressing is applied. However, the pressing increases the density of the tissue web, making it less absorbent and less soft (Liu ). In the same direction, refining increases the density of the tissue web which decreases absorbency and softness (Kullander et al. ). Long fibers promote higher strength because they have higher capability of forming bonds with multiple fibers. Fibers having high curl (curvature) will form tissue paper with lower tensile strength due to the reduction of number of inter-fiber bonds. However, more entanglement among fibers is observed when curly fiber are present in the tissue web, which contributes to higher wet strength and higher tear strength. For a given strength, increasing fiber length or decreasing fiber curl will result in higher bulk (Trepanier ). Higher hemicellulose content also improves bonding strength (Liu ). Because of better bonding ability, virgin and chemical pulps yield stronger tissue products than recycled and mechanical pulps, respectively (Novotny ).

Strength is dependent on the orientation of the tissue with respect to the applied stress (e.g. machine direction, cross direction, thickness direction). Machine and cross direction tensile strengths are usually higher than thickness direction tensile. Due to fiber orientation and creping process, tissue that is evaluated in the machine direction usually has higher strength and higher elongation than when evaluated in the cross direction. This behavior permits tissue products with high elongation capacity to respond better to converting shocks than a stronger tissue with low elongation (Thorp ). Tensile strength measurements performed in commercial kitchen towels shows that products presenting higher elongation capacity usually have better tensile strength (Kan et al. ).

Tensile failure of paper products happens due to a combination of inter-fiber bonding failure and fiber failure. For paper products where the inter-fiber bonding is well developed, such as printing and packaging products, it is expected that the failure of the paper will involve a substantial proportion of fiber failure. On the other hand, in paper products where the inter-fiber bonding is not so well developed, such as tissue products, the failure is more likely to happen as a result of bonding failure (Page ). Therefore, if someone develops a tissue product with very high bonding strength, the tensile failure is more likely to happen as a result of fiber failure. However, bonding strength typically is much less than fiber strength in the case of tissue paper. Therefore, the strength of tissue paper is mostly limited by the strength of the inter-fiber bonding. Many process variables influence the strength and elongation of tissue paper, including, pulping conditions, refining, fiber orientation, formation uniformity, wet pressing, drying tension, creping, and converting. Formation uniformity (sometimes called “uniform randomness”) is an important factor. The basis weight of tissue paper is not the same at all points. As a result, the measured strength represents the strength of the weakest point in the sample. Products having poor formation will be weaker than products with same structural aspects but presenting better formation (Thorp ). In other words, the non-uniform formation can create weaker points in the paper web that will be more susceptible to failure. As a result, papermakers constantly look for process and chemical alternatives to enhance bonding strength (e.g. refining, strength additives) and uniformity of web formation (Hubbe ).

Paper tissue under stress will exhibit visco-elastic behavior. At low strain levels paper behaves elastically (reversibly), where the force increases linearly with strain. Most of the elasticity observed in tissue paper comes from the creping process. When the strain goes beyond the elastic region, tissue paper changes irreversibly, and a slower increase in force is achieved with an additional increase of strain. Force increases to a point where the strength reaches a maximum, called the tensile strength, and this is followed by the failure of the tissue paper at the weakest point. The area calculated below the stress and strain curve represents the energy absorbed by the sample during the tensile test (Thorp ). The energy absorbed is an important property for tissue products. Those products are usually designed to have low density to maximize softness and absorbency. As a result, bonding among fibers is not as well developed as it is in the case of other paper products (e.g. printing, packaging). However, tissue products have to be strong enough to withstand papermaking, converting, and use. Even though those products do not present very high tensile strength (maximum force before failure), they are manufactured to have high elongation capacity, which will give them the capacity to absorb energy during various conditions.

Wet Strength

Paper structure and strength are highly dependent on the level of molecular bonding (hydrogen bonding) among fibers. Due to the hydrophilic behavior of cellulosic fibers, inter-fiber hydrogen bonds are not resistant to moist conditions. However, as mentioned earlier, some tissue products, such as kitchen and hand towels, need to be moisture resistant to be capable of drying and cleaning wet surfaces. In order to maintain some of their strength when wetted, wet strength additives can be used to supplement or replace hydrogen bonding (Hubbe ). Wet strength performance of paper products depends on having a coherent network of fibers reinforced with a crosslinked network of wet strength additives that repress fiber swelling and inhibit fiber-fiber separation. Some wet strength additives, such as urea-formaldehyde, will self-crosslink, forming an insoluble network around contacts among fibers that preserves some of the original dry strength. Besides self-crosslinking, other additives, such as azetidinium resins, will form water-resistant covalent bonds in the cell wall of fibers or between fibers that will reinforce fiber bonding (reinforcement mechanism) (Espy ). The content of fines in the furnish is an important variable because cationic wet strength additives will be preferentially adsorbed on fines, and high levels of fines can be a problem limiting high wet strength performance (Nanko et al. ). Typically, if a paper product can retain more than 15% of its dry strength, it can be regarded as a wet-strength grade. Efficient wet strength additives can retain up to 50% of the dry strength. Besides paper strength improvements in wet conditions, those wet strength additives are known to increase dry strength (Lindström et al. ).

Softness

Softness can be defined as a human sensory response to a texture that is pleasing to touch and provides a feeling of delicate and smooth texture lacking stiffness. In other words, softness is the sensory response obtained when someone strokes the surface with fingers and crumples the tissue by hand. Perceived softness is a result of a combination of several sensorial reactions, including not only tactile perception, but also the audio and visual (color, embossing) perceptions. Softness is a very important property, especially in sanitary applications, where consumers are very sensitive to softness acceptance. Softness is usually divided into surface softness and bulk softness. Surface softness is related to the velvet-like feeling of the paper surface that is perceived by human fingerprints, which depends on fiber type, smoothness and finishing of paper surface (e.g. addition of softeners/lotions, wire marks, creping, embossing). Short and flexible fibers are desirable for surface softness. Bulk softness is an indication of how easily the paper yields when crumbled, which depends on paper stiffness, bulk, and the ability of fibers to move within the fiber web. Bulky and flexible fibers with low bonding ability are desirable for bulk softness (McKinney ; Bhatia et al. ; Hollmark and Ampulski ; Liu ; Kullander ).

Human panels are traditionally used to access softness. The results obtained can be considered as being subjective to the group of people involved in the study, which could be paper specialists or consumers. Because different individuals have different opinions and sensitivity to softness, a large number of people and testing is necessary to obtain valid results. To reduce time and resources, many analytical methods involving physical measurements related to surface or bulk properties have been developed to access softness. Basis weight, thickness, bulk, flexibility, stiffness, compressibility, elongation (stretching), draping, crumple, penetration, sound emission, sound attenuation, and thermal conductivity are some of the bulk properties evaluated in the literature. Some of the surface properties evaluated include smoothness, friction, roughness, and fiber free ends. Yet, there is not an acceptable analytical method that can be used to fully mimic the human perception of softness. Analytical methods that combine measurements related to surface and bulk properties usually have better performance (Bhatia et al. ; Hollmark and Ampulski ; Kullander ).

High bulk paper products tend to have superior bulk softness because bonding strength and bonding area among fibers are not as fully developed. The creping process softens the paper by improving the bulk softness when fibers bonds are broken and sheet extensibility is improved. Creping can also increase the surface smoothness. The number of plies also tends to increase bulk softness (Boudreau ). Calendering can be used to improve surface smoothness (Novotny ). Tissue products made with low coarseness fibers having a large number of free and flexible fiber ends protruding up from the surface present better surface softness. Fibers having higher coarseness are more desirable to give better bulk softness (Kim et al. ; Axelsson ). Higher softness is achieved with the use of curly fibers (Trepanier ). Sulfite and kraft pulps are softer than recycled and mechanical pulps (Novotny ).

TISSUE FACILITIES AND MACHINE TECHNOLOGIES

Tissue Facilities

Tissue products are manufactured in facilities having different configurations and levels of integration. Tissue facilities can be differentiated in terms of pulping and recycling capabilities (integrated and non-integrated) and fiber type (virgin and recycled). Integrated facilities have assets for on-site pulp production and tissue manufacturing. In those mills, the starting raw material can be wood or non-wood when tissue is manufactured with virgin pulps or recycled paper in the case of recycled tissue production. Usually, virgin integrated facilities are more complex, having all the assets necessary to convert wood and non-wood into the paper (e.g. pulping, washing, bleaching, stock preparation, paper machine, chemical recovery, steam and power production, and effluent treatment). Due to process capabilities and high level of process integration, it is common to have virgin integrated facilities that produce not only tissue products but also market pulp and other paper products. Recycled, integrated facilities have the assets to reprocess recycled paper into tissue products (e.g. hydro pulping, washing, deinking, bleaching, stock preparation, paper machine, steam and power generation). Non-integrated facilities do not have any pulping or recycling capabilities. The starting raw material is market pulp (virgin or recycled fibers), and the process configuration is simpler (stock preparation, paper machine, steam, and power production). Recycled integrated and non-integrated facilities are usually more dedicated plants, although facilities that also produce other paper products can be found (FisherSolve International ).

Tissue Machine Technologies

The final properties of tissue products are highly dependent on the tissue machine technology. Light Dry Creped (LDC) (Fig. 1) is the most conventional technology. The main differences between an LDC machine and a conventional, non-sanitary paper machine are the shorter length, Yankee cylinder drier (large steam heated drum), and creping processes. Headboxes used in tissue machines are designed for low consistencies (0.1% to 0.5%), and they are similar to headboxes used in conventional paper production. The basic purpose of a headbox is to evenly distribute the stock on the forming fabric (often called the “wire”) and prevent fiber flocculation by applying turbulence to achieve relatively uniform paper formation. Control of fiber orientation is performed by adjusting the ratio of jet speed and wire speed (Kullander ). Headboxes can also be layered to allow for distribution of different types of furnishes in the center and surfaces of the paper web (Tysén ). For example, the internal layer can be made with long fibers (softwoods) to provide strength, machine runnability and bulk softness, while the external layer can be made of short and thin fibers (hardwoods) to improve surface softness (Axelsson ; Pavan ).

Fig. 1. Sketch of light dry crepe (LDC) tissue machine composed by a crescent former, pressing section, Yankee cylinder and creping blade (Tysén )

There are four main types of forming section used in tissue machines, crescent former, twin-wire, suction breast roll, and Fourdrinier. Nowadays, the most common forming section for tissue grades is the crescent former (Fig. 1), where the stock jet is directed between a forming fabric that promotes the drainage and a felt. Crescent formers provide superior runnability at high speeds (up to m/min) because no transfer between wire and felt is needed. The second most common forming section is the twin-wire ( m/min), where the stock is sprayed in between two wires, promoting efficient dewatering and good control of fiber orientation. In a suction breast roll former (up to m/min), dewatering is controlled by suction, such that water is drained from the space between the top of the headbox and the wire. A suction breast roll former does not allow good control of fiber orientation. The last and oldest type of forming section is the Fourdrinier former. The Fourdrinier is limited in speed (up to m/min) and dewatering happens in one direction through the web by gravity and suction (Pavan ; Kullander ).

Vacuum systems, such as suction boxes or suction rolls, are usually used to increase the consistency to the range of 15% to 25%. Before the LDC drying step at the Yankee cylinder, the paper web is pressed at the press nip (2 to 4 MPa) by a roll press or shoe press to reach a consistency of 40% to 45%. The shoe press has a longer nip and applies lower pressure than a roll press roll, resulting in a bulkier web. The level of pressure used at the press nip is crucial. Minimum pressing is desired for the production of a higher bulk and soft tissue. After pressing, the paper web is dried at the surface of Yankee drier up to a solids content of 94% to 98%. The drying process is performed by the steam-heated Yankee cylinder surface and by hot air flow from the hood above and surrounding the Yankee cylinder (Kullander ). A coating is sprayed on the Yankee surface to promote the adhesion between the sheet and the Yankee and to protect the metal surface of the Yankee from the creping blade (Forbess ).

The creping process is a very important step for the production of tissue products with higher bulk, absorbency, softness, and stretch. During the creping process, the doctor blade scrapes the paper web off from the Yankee surface. Creping delaminates the internal physical structure of the paper web, forcing the fiber bonds to be weakened/broken and forcing the fibers to buckle, become distorted or even broken. Micro-folds also are created and piled up on top of each other, and when the pile is high enough, it falls and creates a macro-folded and structured end product (Fig. 2) (Kullander ; Peters ). The delamination process tends to produce a thicker, more absorbent, and cushiony tissue product with higher water-holding capacity than does the folding type of creping (Nanko et al. ).

Good adhesion between the Yankee surface and the paper web results in a finely creped product that is bulkier, more absorbent, and softer. Good adhesion promotes the proper breakage of fiber bonds and higher frequency of creping folds. Additionally, more fibers are pulled from the paper surface creating more fiber ends that enhances the hand feel (Boudreau ). High adhesion might cause defects or web breaks. Low adhesion may result in low creping frequency and low quality (Sundholm and Huostila ). Good adhesion is achieved with pulps having better bonding ability (Zou b). Refined pulps having higher hemicellulose and higher fines content will promote better adhesion. A tissue web having higher basis weight and higher moisture will also present better adhesion to the Yankee surface (Boudreau and Germgard ). Kraft pulps gives the best adhesion, followed by sulfite and mechanical pulps (Novotny ). Among different mechanical pulps, chemi-thermomechanical pulps (CTMP) have better adhesion to Yankee dryer than Thermomechanical Pulp (TMP) and Groundwood Pulp (GWP) (Sundholm and Huostila ). Typically, the Yankee side of the tissue paper is softer than the felt side. The Yankee side has small valleys that give a softer sensation, while the felt side has peaks that provides a rougher sensation. Therefore, it is recommended to put the Yankee side of the sheet on the outside of tissue products (Boudreau ).

Fig. 2. Creping process and the formation of micro-folds and macro-folds as a function of the angle between the top surface of the creping blade and Yankee surface. Left: small angle. Right: large angle (Raunio and Ritala ).

The angle between the top surface of the blade and the surface of the Yankee drier influences the amount of micro- and macro-folds created in the tissue paper. Values between 40 to 100 degrees are observed, especially in the range of 80 to 90 degrees. Smaller angles creates higher number of macro-folds (piles of micro-folds). This creping process yields a super creped product that is unusual. At higher angles, the macro-folds are not significantly formed (Raunio and Ritala ).

Another important paper machine technology used for tissue manufacturing is the Through-Air Drying (TAD) process. Different from the dry creped machine, the TAD machine does not have a press section, and this helps to preserve the three-dimensional structure of the paper web. Dewatering before the drying section is achieved with vacuum on suction boxes to a consistency of about 20% to 25%. The paper web is transferred to a perforated through-air drying cylinder, where hot air is blown through the tissue web. An imprinting TAD fabric can be used to imprint a knuckle pattern on the tissue web. (Sanford and Sisson ). Usually, the imprinting is performed by sucking the tissue web against the TAD fabric, before the through-air dryer and while the tissue web is in a wet state. In a through-air dryer, the hot air can be blown to the web from the inside of the cylinder or from the outside of the cylinder while the imprinted structure is maintained (Klerelid ). As a result of the low level of pressing and through-air drying, the final tissue product has higher bulk, softness, and absorbency, which makes TAD an ideal technology for the production of premium and ultra grades (Sanford and Sisson ; Klerelid ). However, a TAD machine has higher energy costs (gas and electricity) and around three times higher capital costs than a conventional machine (Kullander ).

In the Creped Through-Air Drying machine (CTAD) (Fig. 3) the through-air system dries the tissue web until a consistency of about 40% to 80%. The partially dried web is finally transferred to a Yankee cylinder, where it is fully dried to about 96% consistency and creped (Sanford and Sisson ).

Fig. 3. Sketch of creped through-air drying (CTAD) tissue machine composed by twin wire former, through-air dryer, Yankee cylinder and creping blade (Tysén )

In early CTAD processes, the weave of the TAD fabric molds the sheet and then the knuckles contact the Yankee, but leaving the pillows un-compressed. This sets a coarser creping pattern on the Yankee (Fig. 4). The pillows remain as absorbent capillary bundles, as compared to the compressed knuckle areas, resulting in a product with good tensile strength but having better softness and absorbency relative to dry crepe tissue paper (Table 4) (Sanford and Sisson ).

Fig. 4. Early TAD tissue product (MD = machine direction) (Adapted from Sanford and Sisson )

More recently, other types of paper machines technologies have been developed, especially in the USA market, such as UCTAD (un-creped TAD), DRC (double re-crepe), ATMOS (Advanced Tissue Molding System), and NTT (New Tissue Technology). UCTAD was developed to decrease limitations in tissue machine speed caused by variable crepe in the TAD process at higher speeds (Fig. 5). The formed sheet is transferred to the molding fabric at about 22% consistency and then on to the TAD dryer to dry to 97% solids content. The lack of a creping process initially resulted in a harsher sheet, but recent advances in surface treatments have ameliorated that (Wendt et al. ).

Fig. 5. Un-creped through-air drying (UCTAD) tissue machine composed by twin wire former and through-air dryer (Adapted from Wendt et al. )

Table 4. Comparison between Early TAD Products and Conventional or Dry Crepe Products

DRC was developed to produce a product that is similar to a two-ply product from a single tissue sheet (Fig. 6). The process is similar to an LDC machine prior to Yankee #1, but then it is creped at 70% consistency (called wet-creped) to delaminate the formed layers, and then imprinted with a latex scrim on each side before sending to Yankee #2 for creping on the other side. This process produces a very soft surface feel but is very expensive (Gentile et al. ).

Fig. 6. Double re-cepre (DRC) tissue machine composed by a fourdrinier former, two Yankee cylinders and latex imprinting stations (Adapted from Gentile et al. ).

ATMOS was developed in the early ’s (Fig. 7). The goal of the newer, more energy efficient process is to use mechanical means to dewater the sheet to 34% to 38% prior to contacting the Yankee with 25% of the sheet as is done with CTAD processes. Transferring at such low consistencies to the Yankee with only 25% contact area puts a significant burden on the Yankee Hood, which must operate at very high temperatures to achieve competitive speeds (Voith, n.d.).

Fig. 7. Advanced tissue molding system (ATMOS) tissue machine (Voith, n.d.)

NTT was designed to overcome some of the limitations of ATMOS by pressing at even higher pressures before transferring to the Yankee (Fig. 8). A shoe press is used in the first pressing section between the Crescent Former felt and a belt with cells designed to provide absorptive capacity and increase strength. Initial production has indicated the ability to achieve up to 45% consistency before transferring to the Yankee, which has reduced the Yankee Hood drying load as compared to ATMOS. However, the high pressures compress the “pillows” of the sheet, which have decreased absorptive capacity as compared to CTAD (Valmet ).

Fig. 8. New tissue technology (NTT) machine (Valmet )

In the late ’s, Procter & Gamble patented a belt to replace the fabric in CTAD. It has the advantage of designing the structure of the molded tissue based on the product’s intended use. The initial belt for a kitchen roll towel is shown in Fig. 9. The lower left schematic is a side view of the belt. It shows a woven “secondary” fabric for belt strength inside a cast urethane belt. A photosensitive urethane resin is extruded around the woven fabric, and the desired pattern is developed by catalyzing the areas that are to remain on the belt. The picture on the right shows one version of the belt after casting. One can see the individual cells for absorbency as well as the secondary fabric that is now part of the belt. The result is a molding belt that provides uncompressed pillows of fiber while also providing lines of high compression that are pressed against the Yankee for tissue strength. This is analogous to replacing the “spot welding” provided by the woven fabric with “continuous welding” with the belt (Smurkoski et al.).

Fig. 9. CTAD belt used to manufacture kitchen towel (Adapted from Smurkoski et al. )

When the various technologies above are compared to each other, they have their advantages and disadvantages as shown in Table 5.

The final step in the tissue manufacturing is the converting process. Converting includes several processes (unwinding, embossing, printing, perforation, winding and tail sealing, log sawing, folding, wrapping, and packaging). Products with two or more plies have inter-ply space, which contributes to higher absorbency capacity. The number of plies also improves tissue strength and softness. The tissue plies are pressed together completely or just at the edges during the embossing process. Embossing is the process where tissue sheet passes in between two engraved steel or rubber rolls having a matched pattern that provides texture to the sheet. During the conversion of tissue having multiple plies, embossing can be applied to each ply separately that are later glued together. The plies can also be embossed simultaneously. The simultaneous embossing can be performed in a foot-to-foot or nested configuration. In the foot-to-foot configuration, the embossing patterns of both plies are aligned to each other, resulting in the creation of suction pockets with superior water absorbency. In the nested configuration, the embossing patterns of one ply are positioned in between the embossing patterns of the other ply. In other others, the “valleys” of one ply fits the “bumps” of the other ply in the nested configuration (Brown ; Enderby and Straten ; Kullander ). Printing is done for appearance purposes and perforation makes the sheets easier to separate. Some final products, such as bath tissue and kitchen towels, are wound onto a paper core and sealed at the tail. After the winding process, the formed rolls are cut into the desired width (10 to 60 cm). Folding is performed on products that are commercialized as individual sheets, such as, facial tissue and paper towel. Packaging is the final converting step in which the products are wrapped in plastic, paper, and boxes (Kullander ).

Table 5. Comparison Among Different Tissue Machine Technologies Highlighting Differences in Products Attributes and Machine Performance (Adapted from Reisinger )

TISSUE PAPER FIBERS

Different fiber types are available in the market for tissue production, and they can be defined according to their source (virgin or recycled), type of process (chemical, mechanical, semi-chemical, bleached, unbleached), type of biomass (hardwood, softwood, non-wood), and biomass species. All those variables will influence the characteristics of the fibers and properties of tissue products. A vast mixture of hardwoods (eucalyptus, northern, southern, tropical), softwoods (northern, southern), and non-woods (straw, bamboo, bagasse) are used for tissue manufacturing. The main sources of recycled fibers are papers originated from offices (SOP – sorted office paper), magazines (OMG – old magazines), newspapers (ONP – old newspaper), boxes (OCC – old containerboard; DLK – doulble lined kraft), and other mixed recycled papers (MP – mixed paper) (FisherSolve International ).

Hardwood and Softwood Pulps

Paper products are usually manufactured with a blend of hardwoods and softwoods. There are two main types of softwood pulps in the USA, southern and northern. Southern softwood pulps are mostly produced from southern pines and radiata pine. Northern softwood pulps are produced from a variety of species (pines, spruces, firs, hemlocks, cedars, Douglas-firs, larches). On the other hand, hardwood pulps are made from a much more diverse group of species and can be divided into two categories, single species, and mixed species. Hardwood pulps will range from 100% aspen, maple or birch to mixed northern or southern species and 100% eucalyptus. Some examples of hardwood pulps include: a) Northern hardwoods: aspen, maples, birches, beech; b) Southern hardwoods: gums, oaks, poplar, ash, beech; c) Eucalyptus species including: grandis, urophylla, globulus, camaldulensis, and hybrids; d) Tropical hardwoods: acacia, mixed tropical) (Nanko et al. ). The benefits of hardwood pulps made of single species, such as eucalyptus in Brazil, have caught the attention of the pulp and paper industry. Brazilian eucalyptus trees are harvested from well-monitored plantations, resulting in a very uniform furnish having narrow particle size distribution and low content of fines. Those characteristics allow better control of paper characteristics and papermaking process, including easier drainage and drying, which are usually limiting factors for high speed tissue machines (Hall ; Pavan ). The third main type of pulp is mechanical pulps, such as chemi-thermomechanical (CTMP), which have a balance of properties from hardwood and softwood species (Fig. 10) (Nanko et al.).

Softwood pulps have long fibers that provide a strong fiber network to increase wet web strength and runnability of the paper machine and subsequent converting operations. Softwood fibers are primarily used as reinforcement fiber in many different paper grades, including tissue products. A strong and continuous fiber network is achieved with softwood fibers that are thin and long (low coarseness to length ratio). Due to its low coarseness to length ratio, NBSK is highly desirable as a source of long fibers and strength without loss of softness that comes with other softwoods (Byrd and Hurter ). Softwood pulps containing low amounts of fines will contribute to maximize the performance of long fibers, minimize chemical usage, lower drainage resistance, increase retention, and reduce paper dusting. Additionally, softwood pulps with higher fiber strength can maximize paper strength, however, tissue products usually require relatively low tensile strength, and fiber strength is not a critical issue. Softwood fibers with a thick cell wall are less likely to collapse during papermaking process and more prone to form thicker and bulkier tissue products with improved structure openness and water absorbency (Nanko et al. ). However, softwoods that are finer having thin cell wall are flexible and capable of providing good softness (Zou a). Higher stretch values are also desired in softwood fibers because they improve paper web runnability and result in lower stiffness and higher softness, although most of the stretch observed in tissue products comes from the creping process. Tissue products made of softwood pulps with low bonding strength are more prone to delamination during the creping process, resulting in a bulkier and softer structure. Higher freeness is better but not a major issue because pulp freeness is already high enough in softwoods. Softwood pulps with high unrefined strength are preferred to maximize bulkiness and achieve desired strength (without or with minimum refining) at same time (Nanko et al. ).

Fig. 10. Morphology of unbleached hardwood and softwood market pulps. BEK: bleached eucalyptus kraft; NBHK: northern bleached hardwood kraft; NCTMP: northern chemithermomechanical pulp; SBHK: southern bleached hardwood kraft; SCTMP: southern chemithermomechanical pulp; TBHK: tropical bleached hardwood kraft; NBSK: northern bleached softwood kraft; SABRPK: South American bleached radiata pine kraft; SAURPK: South American unbleached radiata pine kraft; SBSK: southern bleached softwood kraft; SUSK: southern unbleached softwood kraft (Adapted from Nanko et al. )

Hardwood pulps are primarily used for their ability to provide good formation, a smooth surface, finer pore structure, and high opacity. In tissue products, hardwood fibers also provide bulk, softness, and a velvet type surface feel. Hardwood pulps are used in most tissue grades at levels ranging up to 100%, but more typically 50% to 80% of the fiber furnish (Nanko et al. ; Zou ). To develop strength without losing softness provided by hardwoods, refining can be applied only on softwoods (McKinney ). Among different types of hardwood pulps, eucalyptus pulp is capable of achieving tissue with high bulk, absorbency, and softness (Byrd and Hurter ). Eucalyptus pulp has low fines content, a high population of short fibers with thick cell wall, and low coarseness, which complement the softwood matrix by providing sufficient strength with many free fibers ends to give a soft velvet feel preferred by consumers. The high fiber population of eucalyptus fibers provides a uniform paper structure that facilitates uniform drying (Hall ; Nanko et al. ). On the other hand, high fiber population results in limitations for papermakers in terms of fiber retention on machine wire and dusting and linting in converting operations (Nanko et al. ). As reported by Foelkel (), to achieve high bulk, tissue makers should seek eucalyptus pulps having: a) high coarseness to minimize fiber collapsibility and sheet densification; b) low content of fines to avoid densification, build up in the paper machine white water, and reduction in drainability; c) low hemicellulose content for reduced bonding ability; and d) high fiber deformation (e.g. curl, kinks) to improve bulk, sheet porosity and absorbency. Another advantage of eucalyptus pulp is the low content of extractives, which results in improved absorbency and lower deposition of extractives on paper machine. At the same drainage rate, eucalyptus fibers provide good wet web strength when compared to other hardwoods. Eucalyptus is suitable for the production of high quality tissue paper, for which light refining is recommended (22 < Schopper Riegler degrees < 35). The content of eucalyptus in those products can vary from 50% to 60% in napkins, bath tissue and towels to 100% in facial tissue (Hall ).

Mechanical pulps can be used to provide increased void volume (bulk) and water holding capacity to tissue products. The higher content of lignin gives mechanical pulps a more rigid structure in the wet state when compared to low yield pulps, which contributes to maintaining the water holding capacity (Nanko et al. ; Yuan et al. ). On the other hand, a high content of fines present in mechanical pulps will increase the density of tissue paper and give problems with dusting and linting (Axelsson ). A self-sizing mechanism can reduce absorbency rate during storage. Peroxide bleaching can be used to overcome the self-sizing phenomenon and improve absorbency rate due to reduction of extractives content. Peroxide-bleached mechanical pulps also have higher brightness, lower fiber stiffness, better fiber bonding, lower dusting, better brightness stability, and lower slushing time (Johnsson ; Norwegian Pulp and Paper Research Institue ). Mechanical pulps have small impact in bulk softness but a negative effect on surface softness. In order to minimize the negative impact on softness, it is recommended the use of mechanical pulps having the least amount of shives (Norwegian Pulp and Paper Research Institue ). Because mechanical pulps lack the desirable properties for tissue products (e.g. softness, strength) to some extent, they are usually blended with other fibers for tissue manufacturing. Up to 50% of mechanical pulp can be used in tissue products without significant change in strength (Johnsson ). Bulk and absorbency of towel and bath tissue can be increased with fibers blends having from 5% to 30% of mechanical pulps without significant reduction of softness, strength, and brightness. However, brightness reversion can still be a problem (Yuan et al. ; Zou ). A comparison between different types of mechanical pulps for tissue applications shows that CTMP provides better strength than Thermomechanical Pulp (TMP) and Groundwood Pulp (GWP) due to better bonding ability. GWP presents the lowest strength. Better absorbency rate and capacity is expected for CTMP pulp. On the other hand, due to the self-sizing phenomenon, absorbency of TMP and GWP is negatively affected (Sundholm and Huostila ; Norwegian Pulp and Paper Research Institue ). TMP is softer than GWP (Novotny ).

It is important to highlight that the properties observed in tissue products are a result of the morphological and physicochemical characteristics of the fibers used. In other words, fiber composition and morphology are determinant for tissue properties (Muller and Teufel ). As it can be seen from Fig. 10, there is a significant difference in morphology among different types of biomass (e.g. softwood, hardwood, non-wood). Additionally, pulps coming from different biomass species will also have different morphologies to some extent. For example, different softwood and hardwood pulps produced in different geographic regions from different species have different fiber morphology. Each one of those particular morphological features will defined their performance in different tissue products (Nanko et al. ; Zou a).

Non-Wood Pulps

Typically, woody biomass is the preferential raw material used for pulp and paper production due to low cost, wide availability, little content of the non-fibrous material, ease of processing, and uniformity (Roncero et al. ). Although the world production of non-wood pulp in was only 6.5% of world wood pulp production (FAO b), non-wood biomass has a long history in pulp and paper industry and can also be considered an important source of raw material. Non-wood fibers can be used as an alternative to: a) provide local raw material security against imported market pulp, b) develop “green” products for consumers with environmental preferences, c) minimize environmental pressure and impacts related to handling of agricultural residues (e.g. burning and landfill practices), d) develop local markets where wood fibers are scarce and expensive, e) reduce pulp costs where non-wood biomass is abundantly available and cheap, and f) improve desired properties or give different characteristics to paper products (Byrd and Hurter ; Phillips et al. a,b; Zou and Liu ). For example, in Europe and the Americas, where wood fibers are more readily available than in Asia, the production of non-wood pulp represents only 12.3% and 8.4% of the world production, respectively. On the other hand, Asia, mainly represented by China and India where wood biomass is scarce, produces around 77.4% of world’s non-wood pulp (FAO b). However, non-wood fibers are also being used for tissue manufacturing in other regions, such as North America, as a part of sustainability programs (Byrd and Hurter ; Zou and Liu ).

Non-woods usually provide higher raw material yield than wood and can be obtained from annual plants (planted and harvested annually) or perennial plants (planted once and harvested in multiple years). Non-wood fibers can be obtained from agricultural residues originated from cereal and grain plantations or from fiber crops that are specifically planted as a source of fiber (Byrd and Hurter ). Non-wood feedstocks usually have a much wider range of fiber lengths among different species. Many non-wood species, such as straw, bagasse and other agricultural residues, have similar fiber length as hardwoods. Other species, such as flax, hemp and kenaf, have a fraction of long fibers that have to be shortened before papermaking. Some non-woods, such as abaca, flax, hemp, sisal, and kenaf have the same or better properties than softwoods. Regarding morphological features, some substitutes for NBSK include abaca, bamboo, hemp, hesperaloe, kenaf, and sisal, while some substitutes for BEK include bamboo, bagasse, corn stalks, sorghum stalks, and wheat straw. Therefore, careful selection of the raw material is necessary to achieve the desired paper properties, considering the wide range of fiber characteristics found in non-wood biomass. Some of the problems associated with the processing of non-wood biomass are: a) high costs and logistic problems (harvesting, transportation, storage) associated with the bulky raw material, b) control of material decay during the storage in between harvesting seasons, c) high content of silica that makes the chemical recovery difficult, d) poor drainage of produced pulps due to the high content of fines, e) high raw material chemical and physical variability, and f) agricultural residues tend to have low strength. However, some non-woody biomass, such as, bamboo, reed, and switch grass are denser, allowing easier processing and transportation. Additionally, non-wood fibers usually have a lower content of lignin and are easier to pulp (lower temperature and chemical charge). Straw, bamboo, and sugarcane are among the most used sources of non-wood biomass (Leponiemi ; Byrd and Hurter ; Zou and Liu ).

Wheat straw is a byproduct of wheat production. Approximately 3 tons of wheat straw are generated per acre. While about 0.5 tons are necessary to contribute to soil quality and to control erosion, the excess may cause problems with subsequent field operations (e.g., no-till seedling, fungal diseases). Some of the alternatives used to avoid those concerns are the practice of burning the straw and tilling it into the soil. Therefore, wheat straw represents an opportunity for wood fiber substitution. Wheat straw is composed of leaves (9% w/w), nodes (11% w/w), and internodes (80% w/w). Fibers present in each fraction of wheat straw have different fiber length (internodes = 1.20 mm; leaves = 0.79 mm; nodes = 0.65 mm) and number of fine particles (internodes = 24%; leaves = 49% mm; nodes = 51%) (McKean and Jacobs ). Moreover, only about 1/3 of the cells in wheat straw are fibers. The remaining cells are non-fibrous cells (vessels, parenchyma cells, epidermal cells) that are shorter (less than 0.5 mm) and wider (up to 150 µm) than fibers (Singh et al. ). The whole wheat straw has a weighted fiber length around 1.0 mm, with a width around 46 µm having a very low coarseness (4.5 mg/100 m) (McKean and Jacobs ). On the other hand, wheat straw fibers have weighted fiber length around 1.2, with a fiber width around 15 to 20 µm (McKean and Jacobs ; Singh et al. ). Wheat straw fibers have high slenderness ratio (fiber length/fiber width = 87), low flexibility coefficient (100 x lumen diameter/fiber width = 42), and high Runkel ratio ( 2 x cell wall thickness / lumen diameter = 1.4), resulting in a low degree of collapsing and conformability, which gives more porosity and bulk to the paper web. Wheat straw has a high content of extractives, which decreases the pulping yield, and high content of hemicelluloses, which contribute to strength properties (Singh et al. ). Wheat straw required 1/3 of the refining energy applied to eucalyptus to achieve similar burst and tensile strength and higher bulk. Wheat straw has a much higher drainage resistance due to the high content of fines. Unrefined wheat straw presented 37° Schopper Riegler (SR), which is a higher value than the usual drainage resistance used in tissue machines (25° SR) Roncero et al. (). Additionally, the high content of primary fines may result in low fiber yield, higher paper density, and lower paper strength. The high content of inorganics found in wheat straw, especially silica, causes problems with chemical recovery and deposits/corrosion of equipment. Preprocessing can be used to separate wheat straw components with less desirable properties (dirt, inorganics, leaves, nodes, pith/parenchyma cells), which will decrease the content of fines and inorganics, and improve pulping yield, recovery process, drainage, and paper strength (McKean and Jacobs ).

Sugar cane bagasse is a byproduct of the sugarcane industry. After crushing sugarcane stalks to extract sucrose juice, the remaining fibers are called sugarcane bagasse. Typically, 1 tonne of sugarcane stalks (70% moisture content) generates about 135 kg of bagasse. The majority of bagasse is usually burned inside sugarcane mills to generate steam and power (Bonomi et al.). The excess bagasse can be used as a source of fiber for paper products. Around 60% to 70% of bagasse mass is composed of useful fibers. The remaining mass is represented by non-fibrous parenchyma cells (pith) and soluble matter (Agnihotri et al. ; Lois-Correa ). Due to its high content of pith, bagasse has high dewatering resistance and poor paper properties (Rainey ). Depithing is a known preprocessing step used to remove the majority of the non-fibrous fibers before pulping. Depithing not only removes non-fibrous material but also reduces the amount of dirt and inorganics and produces paper with better quality (Lois-Correa ). Depithing improves dewatering, strength and pulping yield of bagasse (Rainey ). The fiber length of depithed bagasse is around 1.5 mm, and they have a width of about 20 μm. Parenchyma cells and vessels have a wide range of particle sizes and are shorter and wider than fibers. When compared to hardwoods, bagasse fibers have high Runkel ratio (2.5), high slenderness ratio (71), and low flexibility coefficient (29), resulting in low flexibility, low fiber bonding, and high bulk. The high content of extractives and ash contributes to lower pulping yield and operating process associated with inorganics. The high quantity of ashes cannot be considered so problematic since the silica-based salts are negligible. High hemicellulose content benefits the paper strength (Agnihotri et al. ).

Bamboo is a non-wood biomass with a high growth rate (up to 27 OD tonne/year acre) having long and semi-long fibers with properties in between hardwood and softwood fibers. Bamboo has lower content of fines, higher density, and is better resistant to storage degradation than other non-woody biomasses. Bamboo is composed by culms or internodes (most desirable source of fibers), nodes, and branches that rise from nodes and leaves (Phillips et al. a). The average length of bamboo fibers is around 2.0 mm. The average width of bamboo fibers is around 18 μm, and fiber coarseness is around 5 to 9 mg/100m. However, the weighted average fiber length of bamboo pulp is reported to be around 1.2 mm due to the high content of short fibers (Nanko et al. ; Cao et al. ; Phillips et al. a). There are differences in the morphology of fibers found in internodes and nodes. Nodes have much shorter (0.7 mm) and wider (30 μm) fibers than internodes (length = 2.5 mm; width = 11 μm). Nodes have a much higher content of fines. Therefore, the presence of the nodes significantly reduces the average fiber length, which negatively impacts drainage and paper properties. De-knotting before pulping using suitable screening techniques is a process alternative to improve paper quality (Cao et al. ). Different values for Runkel ratio (1.5 to 3.5), slenderness ratio (70 to 160), and flexibility coefficient (20 to 40) have been reported in the literature (Singh et al. ; Cao et al. ). Bamboo has lower lignin content than softwoods and hardwoods requiring milder pulping conditions. The hemicellulose content of bamboo is also higher than wood biomass. Bamboo nodes have a higher content of lignin, inorganics, and silica than bamboo internodes (Cao et al. ). Bamboo can present pulping yields similar to hardwoods. Bamboo pulps can have fiber properties, such as, fiber length and coarseness, and paper properties, such as, softness, bulk, and strength that area in between the observed properties of hardwoods and softwoods pulps (Byrd and Hurter ; Phillips et al. b; Zou and Liu ).

Virgin and Recycled Fibers

Virgin fibers are fibers that were never converted in paper products and are fresh from wood pulping. On the other hand, reprocessed fibers that have been converted into paper products one or more times are called recycled or recovered fibers. The properties and characteristics of virgin and recycled fibers are different, although most of those differences are subtle. Physical and chemical changes occur as a result of various processes involved during papermaking, paper use, and paper recycling (e.g.additives, pressing, drying, printing, storage, converting, repulping, deinking, and bleaching). Detailed reviews on the impact of recycling process on fiber and paper properties were published by McKinney () and Hubbe et al. (). An overview of these and other works is presented here.

It is expected that a recycled paper would have fibers with a wide range of age or recycling cycles (Göttsching and Stürmer ; Hubbe et al. ). The physical characteristics of recycled fibers change with the number of recycling cycles, reaching a plateau after about four or five cycles of repulping and drying (McKinney ; Hubbe et al. ). However, the first recycling cycle contributes to major changes in the properties of cellulosic fibers (McKinney ).

During the papermaking process, a significant portion of wet-end additives tend to remain associated with the fibers even after recycling. A portion of the fillers that are highly present in some recycled paper grades are not completely eliminated during the recycling process (Muller and Teufel ). Hydrophobic effects of sizing agents may partially survive after recycling and can reduce the wettability and strength of paper products (McKinney ; Hubbe et al. ). Dry strength additives, such as cationic starch, can still contribute to the strength of paper after recycling. However, the impact of recycled additives in paper properties will practically be eliminated when fibers are recycled multiple times. Wet pressing will decrease water-holding ability due to closure of voids inside the cell wall (McKinney ). Irreversible loss of swelling is observed when fibers are pressed at consistencies above 30% to 35% (Maloney et al. ). The drying process renders a hydrophobic character to cellulosic fibers, and there is a reduction of swellability or hornification (Muller and Teufel ; McKinney ). This behavior is more pronounced in chemical pulps, especially when they are refined. The porosity, fibrillation, and cell wall delamination of refined chemical pulps are partially reversed during the drying process, which contributes to the reduction in swellability. Because mechanical pulps are not as porous and fibrillated as chemical pulps, their swellability loss caused by the drying process is much less pronounced. Paper drying semi-irreversibly closes nano-sized pores, decreases external surface area, decreases flexibility and conformability, and makes the fibers more susceptible to breakage when they are further refined. Calendering can reduce fiber swelling capacity and fiber damage (McKinney ; Hubbe et al. ). Printing also has a negative effect on recycled fibers. The presence of black or colorful dots in the final product is related to the incomplete elimination of ink fragments during the recycling process (Muller and Teufel ; McKinney ). Additionally, inks are usually hydrophobic materials that will reduce the bonding ability and increase the cationic demand of fiber furnish (Hubbe et al. ). Converting processes, such as gluing, will increase the content of contaminants in recycled fibers. High levels of wax, adhesives, and wet-strength agents can cause various problems during the recycling and papermaking process. Deposits on wires, felts and cylinders may cause holes and weak points in the tissue web (Muller and Teufel ; Grivas ). The storage of paper products at high temperatures will cause embrittlement of fibers and accelerate the decomposition of cellulosic chains (Hubbe et al. ).

Recycling operations may or may not interfere in the quality of recycled fibers. Mechanical processes executed at high consistencies (e.g. pulping, dispersion, bleaching) increases fiber curl which yields a bulkier paper web with reduced strength. The removal of fillers during the recycling process (e.g. deinking, cleaning) increases drainage rate, tissue strength, bulk, and absorbency (McKinney ). Fiber recycling may reduce the content of hemicellulose, which will hurt the strength of recycled paper. Recycling can also cause redistribution of extractives on fiber surfaces, resulting in lower wetting ability and reduced strength. Despite the high level of energy used during aqueous repulping of recycled paper, little damage to fibers is expected to occur during that operation (Hubbe et al. ). The use of sodium hydroxide during pulping improves fiber bonding ability due to cleaning of fiber surface and enhancement of fiber swellability (McKinney ; Hubbe et al. ). Deinking processes may have positive and negative effects. Deinking reduces the level of inks, stickies, dirt, and fines, and deinking per se does not significantly damage or degrade physical properties of fibers. However, some of the chemicals used during deinking (e.g.fatty acids, surfactants, dispersants, bleaching chemicals) will remain with the fibers. Some deinking chemicals can improve inter-fiber bonding by removing oleophilic particles from fibers. Nonionic surfactants used for deinking tend to act as wetting agents (Hubbe et al. ). Surfactants lower surface tension and reduce the bonding between fibers (McKinney ). The use of fatty acids and calcium as deinking chemicals can reduce paper strength and operating efficiency of the paper machine. It is important to point out that generally, the better the cleaning and deinking processes, the better will be the properties of recycled fibers. Cleaner pulps can be achieved with a higher reject rate during cleaning and deinking. In other words, recycled pulps with better properties and operating characteristics can be obtained by sacrificing some of the fiber yield (Hubbe et al. ).

The papermaking and recycling processes causes surface and bulk changes on cellulosic fibers. Recycled fibers have lower swelling ability and wet-flexibility, especially in the case of once-dried kraft fibers, resulting in reduced inter-fiber bonded area and bonding strength. Recycled fibers are shorter and have higher content of fines than virgin fibers (McKinney ; Hubbe et al.). Additionally, when kraft fibers are refined before been dried during the papermaking process, a subsequent larger loss in fiber bonding is expected when the same fibers are recycled (Hubbe et al. ). In the case of mechanical pulps, the recycling process increases the collapsibility and flexibility of fibers, resulting in better inter-fiber bonding and improved paper strength (McKinney ; Hubbe et al. ). Among different types of mechanical pulps, CTMP pulp has a faster response to recycling process than TMP and GWP pulps. CTMP pulp has lower wall rigidity than other mechanical pulps (McKinney ).

In order to improve the strength limitations found in recycled fibers, mechanical refining is a common approach used by papermakers. However, refining of recycled fibers has to be considered with caution. Most of the recycled fibers have been refined once, and recycled fibers are expected to be more prone to fragmentation than virgin fibers. Refining of once dried fibers will only recover part of strength lost. Losses of bonding ability are observed even when recycled fibers are refined again to the same level of freeness reached before they were first dried (McKinney ; Hubbe et al. ). When recycled fibers are refined to reach similar strength of virgin fibers, significant decrease in drainage rate is observed (McKinney ). The use of high-intensity refining can be expected to exceed tensile strength of some fibers, increase a number of fines and decrease the drainage rate. The use of high consistency refining can be considered a better alternative for refining recycled fibers. High consistency refining will reduce the likelihood of contact between the refiner surface and fibers that tend to cause fiber fragmentation (de Ruvo and Htun ). Another usual approach to minimize the limitations of recycled fibers is to blend them with flexible and fibrillated virgin fibers. High pH conditions can also be used to restore the swelling and flexibility of fibers, although this approach will cause significant delignification. Limitations in inter-fiber bonding can also be overcome by wet end additives (e.g. cationic starch) (McKinney ; Hubbe et al. ).

Recycled fibers generally contribute to reduced bulk and surface softness when compared to virgin fibers. Recycled fibers are stiff and are not able to provide the desired flexibility necessary for good surface softness. Although the recycling process reduces fiber bonding ability, recycled fibers have been previously refined and they have higher bonding ability than unrefined hardwoods, resulting in reduced bulk softness (McKinney ).

However, the differences between recycled and virgin fibers can also be advantageous for tissue products. Recycled fibers have lower swellability and are stiffer and more dimensionally stable, resulting in a paper with higher bulk and absorbency (McKinney ; Hubbe et al. ). Recycled fibers can potentially be used to decrease the inter-fiber bonding (Muller and Teufel ). It is important to understand that different types of recycled fibers will be suited for applications where they perform well and are more economical (Hubbe et al. ).

Tissue layering and multiple plies are alternatives to maximize the performance of tissue products containing recycled fibers. For example, the use of multilayer headboxes allows the application of recycled fibers at the inner side of the ply. On the same direction, three-ply tissue can have recycled fibers in the center to give strength and virgin fibers in the outer plies to give softness (Grivas ). In the case of products manufactured with 100% recycled fibers, improved performance can be achieved using advanced technology (e.g TAD), embossing, and additives (McKinney ).

Mechanical and Chemical Pulps

Cellulosic pulps can also be obtained by chemical (e.g. kraft, sulfite) and mechanical processes (e.g. thermomechanical) or a combination of both methods. Mechanical pulping, especially when carried out at higher temperatures, usually separates fibers at the lignin-rich middle lamella. As a consequence, the external surfaces of mechanical fibers tend to be rich in lignin, which is somewhat hydrophobic. By contrast, removal of lignin and extractives during chemical pulping and bleaching results in fiber surfaces that are rich in carbohydrates and capable of forming stronger inter-fiber hydrogen bonding. Mechanical pulping also tends to separate fibers into a wide range of sizes due to partial breakage of tracheids and fibers, which tends to increase the content of fine particles. On the other hand, chemical pulping tends to leave the fibers relatively intact. Porosity is also different between chemical and mechanical fibers. Mechanical fibers usually have pores larger than 1 nm, while never-dried chemical fibers have pore sizes in the range of 2 nm to 100 nm due to the selective removal of lignin domains during pulping and bleaching (Hubbe et al. ). As a result of those differences, chemical pulps are more flexible and conformable; more readily flatten into ribbon-like fibers that tend to form stronger inter-fiber bonding. Chemical pulps can also be bleached to higher brightness. On the other hand, mechanical pulps are bulker, stiffer and less conformable; the lumen structure tends to be more resistant to the papermaking process (Johnsson ; Hubbe et al. ). Increase in tissue bulk is expected when mechanical pulps are used to replace northern pulps, such as birch and pine. However, increase in bulk will be negligible if mechanical pulp is used to replace BEK (Norwegian Pulp and Paper Research Institue ).

Chemical pulps tend to be more expensive than mechanical pulps because of the pulping yield. The pulping yield of chemical pulps is around 45% to 55%, while mechanical pulps can have pulping yields as high as 98% (Johnsson ; Norwegian Pulp and Paper Research Institue ; Yuan et al. ).

Mechanical pulps are much less susceptible to changes during drying and recycling. On the other hand, chemical pulps are more susceptible to those changes, especially when they are bleached and refined. The opening of voids within the cell wall, by removal of lignin and application of mechanical refining, make the cellulosic fibers more susceptible to changes during drying process, which causes a reduction of strength. On the other hand, recycling of mechanical fibers can increase their flattening tendency which may result in denser and stronger paper (Jang et al. ; Hubbe et al. ).

As a result of the mechanical action, mechanical pulps have higher content of fines and lower freeness than chemical pulps (Johnsson ). The high content of fine particles present in mechanical pulps affects the final properties of tissue products. Higher content of fines typically improves the strength of tissue. On the other hand, fine particles that are present in mechanical pulps or created during the refining process can significantly decrease absorbency rate of tissue paper made with CTMP and 60% northern softwood kraft. The decrease in absorbency rate can be even higher when the effect of fine particles is combined with dissolved organics, such as extractives and lignin, due to its hydrophobic behavior. This can be a problem, especially for tissue mills operating with high content of recycled water. On the other hand, fines improves dry and wet strength due to better inter-fiber bonding and better formation, while dissolved organics have a negative effect on strength (Springer and Pires ). Redistribution of wood components is also an important factor when mechanical and unbleached fibers are recycled. Those fibers have a higher content of wood resins that may cause self-sizing when redistributed in the fibers during recycling, resulting in increased resistance to wetting and strength reduction. However, surfactants can be used to overcome self-sizing effect. Additionally, deinking operations and successive recycling cycles will tend to decrease the extractives content of recycled fibers (Hubbe et al. ).

IMPORTANCE OF MECHANICAL REFINING

Mechanical refining is an important step to prepare fiber for papermaking. The goal of mechanical refining is to apply compression and shearing forces so that fibers will develop the required conformability, bonding capability, and tendency to form bulky or compact paper structures. On a typical refiner, the fiber stock passes between a rotor and a stator, causing fibrillation at the fiber surface and detachment of fines. Additionally, refining also promotes delamination within the cell wall which increases the wet-flexibility of fibers. The refining action also opens submicroscopic spaces within the cell wall and increases swelling and flexibility (Hubbe et al. ). As a result of the physical modifications, refining will improve bonding ability and conformability of fibers, which will result in a denser and stronger paper product. However, refining has to be used with caution during the manufacturing of tissue paper. Tissue products usually require relatively low levels of strength that can be achieved with moderate mechanical refining. The energy input in tissue refiners is normally lower than in conventional papermaking. Low refining energy not only contributes to the production of a bulkier, softer (Kullander ), and more absorbent paper structure but also avoids excessive reduction of water drainage rate and paper machine speed due to the increased fiber capacity to hold water. Typically freeness values for tissue machines are about 500 mL (Canadian Standard Freeness) (Watson and Janssen ).

Besides the total amount of energy used during refining, the refining intensity is another important variable. Refining intensity or specific edge load is a function of the design of the refining plates and can be defined as how hard the fibers are hit during the refining process. Coarse refining plates give higher specific edge load. Refining can also be performed at low consistencies or high consistencies. Low consistency refining is the most common refining option used for tissue manufacturing. However, the interest for high consistency refining is increasing. During the high consistency refining, fibers experience less interaction with the surfaces of the refiners when compared to low consistency refining (Peters ; Zou b). The target for tissue products would be to achieve the desired strength applying minimum refining energy without compromising softness and absorbency (Gigac and Fišerová ).

Another important aspect of mechanical refining is how different pulp types and fiber species respond to refining action. It can be seen from Fig. 11 that there are significant differences in freeness and refining requirements among different types of market pulps. For example, for the same CSF (Canadian standard freeness), NBSK pulps yield stronger paper web than SBSK pulps on average. However, refined NBSK pulps result in lower paper bulk than SBSK pulps. When hardwood pulps are refined, SBHK pulps yield stronger paper web than BEK pulps. On the other hand, SBSK pulps tend to form a denser paper web than BEK pulps. A comparison between softwood and hardwood pulps shows that, although hardwood pulps are not as strong as NBSK pulps, their strength can approach the strength of SBSK pulps and weak NBSK pulps. Therefore, paper properties can be adjusted with proper combination and refining of hardwood and softwood pulps (Nanko et al. ).

Fig. 11. Breaking length and bulk, as a function of freeness. NBSK: northern bleached softwood kraft; SBSK: southern bleached softwood kraft; SABRPK: South American bleached radiata pine kraft; SAURPK: South American unbleached radiata pine kraft; NBHK: northern bleached hardwood kraft; SBHK: southern bleached hardwood kraft; BEK: bleached eucalyptus kraft; TBHK = tropical bleached hardwood kraft; DIP: deinked pulp (Adapted from Nanko et al. )

Effect of Mechanical Refining on Tissue Properties

Water absorbency, softness, and strength can be defined as the most important properties for tissue products. As discussed before, those desired properties are a function of technology, fibers, chemical additives, and mechanical treatment used during the tissue making process. Refining is a very common mechanical method used to modify the characteristics of fibers and achieve the desired properties of paper products.

Kullander et al. () and Gigac and Fišerová () evaluated the impact of refining on strength, water absorption capacity and bulk softness (measured as flexural rigidity) of bleached kraft softwoods (spruce, pine), bleached kraft hardwoods (birch, eucalyptus), and bleached sulfite spruce. Refining results in fibrillation and fiber straightening, which increases flexibility, bonding ability and bonding area of fibers, resulting in stronger and denser paper webs. Refining significantly reduced the weighted fiber length of spruce sulfite. No significant fiber shortening was observed for kraft fibers because kraft fibers tend to be stronger than sulfite fibers.

A comparison between wood types shows that kraft hardwoods presented similar or better dry and wet tensile indexes than kraft softwoods at the low refining levels (< PFI revolutions), which may seem to be unexpected. However, fiber length is not the only morphological aspect impacting tensile index. The increasing number of fibers in hardwood can compensate for the shorter fiber length. On the other hand, based on the same dewatering resistance, kraft softwoods presented higher dry and wet tensile indexes. Kraft spruce and pine presented the best tensile index, followed by birch and eucalyptus. Sulfite spruce showed the lowest tensile index. The advantage of softwood fibers on tensile strength diminishes as the grammage decreases, probably due to structural differences at low grammage. Additionally, the probability of encountering a weak spot in softwood sheets is higher due to the presence of a more open or porous fiber web. The relative bonded area might also be higher in hardwoods sheets due to better fiber coverage (Kullander et al.; Gigac and Fišerová ).

Unbeaten softwoods presented higher water absorption capacity. Eucalyptus showed the lowest absorption capacity due to the more closed porous structure among all unrefined samples. Water absorption decreased for all pulps evaluated within the refining range of 20° to 45° SR due to the lower content of air spaces between fibers. Hardwoods (birch and eucalyptus) presented better absorption than spruce at same dewatering resistance. Spruce kraft showed better water absorption than spruce sulfite. It is usually observed that kraft pulps have better water absorption than sulfite pulps (Kullander et al. ; Gigac and Fišerová ).

The response of refining on bulk softness depends on many factors, such as wood type, fiber species, and the types of pulping and bleaching. Overall, hardwood pulps presented similar or better bulk softness than softwood pulps. Among the hardwoods, TCF bleached birch kraft exhibited better bulk softness than ECF bleached eucalyptus kraft. Refining increased birch softness in the refining range evaluated (20° to 45° SR), however bulk softness for eucalyptus and spruce decreased at low refining degree (less than 25° SR), followed by an increase at higher refining degree (25° to 45° SR). Sulfite spruce presented better bulk softness than kraft spruce due to a higher flexibility of sulfite pulps. TCF bleached kraft spruce kraft presented better bulk softness than ECF. However, no significant differences in bulk softness were observed between TCF and ECF bleached spruce sulfite (Gigac and Fišerová ; Kullander et al. ).

Refining consistency was studied at laboratory and mill scale by Wang and Chen (). Non-wood and wood fibers were refined at low (1.6% to 4.3%) and high (18% to 30%) consistency. Because of the lower number of shearing and compressive interactions experienced between fibers and refining plates, high consistency refining reduces fiber cutting and fines production, yielding more fiber deformations (curl and kink). High consistency refining resulted in same bulk, better strength (tear and tensile), and lower refining energy consumption when compared to low consistency refining at same freeness level.

Mechanical refining of non-woods (bagasse, wheat straw and rice straw) has also been studied. Very light refining has shown to increase the number of fines for the whole non-wood pulps due to loosening of parenchyma cells aggregates. Fines content also increased when only longer fiber fractions (fibers retained at 200 mesh and 50 mesh screening) of the pulps were refined. However, the source of the fines depends on the type and strength of the fibers. External fibrillation has caused an increase in fines content in the case of bagasse and wheat straw fibers, while fiber shortening was the main source of fines production during the refining of rice straw fibers. The removal of non-fibrous fines yielded a stronger sheet at a given freeness (Roy et al. ). The level of energy applied during the refining of non-wood fibers is also an important variable. The use of high specific edge loads during the refining of wheat straw and bamboo caused the disaggregation and disintegration of parenchyma cells, resulting in rapid decrease of drainage and denser paper web. Parenchyma cells have thin cell wall that can be more easily disintegrated than fibers under mechanical action. On the other hand, refining at lower specific edge loads shown better bulk and strength due to better preservation of the physical integrity of fibers (Subrahmanyam et al. ).

The effect of refining intensity on wood pulps for tissue making has also been studied. However, the results are contradictory. Zou (b) showed that low specific edge load gives better tensile strength and bulk at a given refining energy or drainage for NBSK pulp. On the other hand, Gigac and Fišerová () showed that higher specific edge load improves bulk softness and absorbency for different bleached hardwood and softwood kraft pulps.

Trepanier () has discussed the impact of refining energy on fiber length and curl (fiber curvature) and kink (abrupt change in fiber curvature). The use of low energy (60 kWh/o.d. metric ton of pulp) during low consistency refining does not change the fiber length, but it significantly reduces fiber curl and kink, which increases tissue paper density. Subsequent increase of refining energy does not change fiber curl and kink significantly, but a reduction of fiber length is observed.

FINAL CONSIDERATIONS

Although there is a vast number of publications evaluating the use of different fibers on writing, printing and packaging paper grades, fewer peer-review works have been published dealing with tissue manufacturing. As noticed by other authors (e.g. Hall ), the lack of scientific research on tissue paper is probably a result of high competition and secrecy among different tissue producers and suppliers. There is a lot of opportunity to explore the effect of fibers, especially non-wood fibers, chemical additives, and process alternatives on tissue properties. Additionally, there is a need for standard procedures to make and test tissue products. Several works on tissue products use pressing to form handsheets at laboratory scale. Pressed handsheets will present much higher apparent density than the usual values found in tissue products (from 150 kg/m3 to 350 kg/m3), resulting in poor absorbency and softness. In order to better mimic the tissue making process, standard handsheets can be lightly pressed or not pressed at all. As discussed before, density is a very important property for tissue products and can be considered as the major difference between tissue and other paper grades.

SUMMARY STATEMENTS

Machine technology and fiber type significantly affect the final properties of tissue products. Conventional technology, such as dry-crepe, uses pressing to partially dewater the paper web, which promotes the reduction of bulk resulting in poor softness and absorbency. Advanced technologies, such as Through-Air Drying (TAD), produce tissue products with high bulk, softness, and absorbency.
Different types of fibers and pulping process contribute to different aspects of tissue products (Table 6). Softwoods are mainly used as a source of reinforcement, while hardwoods provide softness. Non-wood biomass has a wide range of fiber morphology with properties similar to hardwoods and softwoods, depending on the species. Mechanical pulps have stiff fibers and can be used to create a bulkier paper web. Chemical pulps are flexible and conformable, resulting in better bonding ability combined with better softness. Virgin fibers are more flexible and produce stronger and softer tissue products. On the other hand, recycled fibers are stiffer with lower bonding ability and have higher content of short fibers and fines, yielding tissue products that are weaker and less soft.

Table 6. Properties of Fibers Used in Tissue Products

3. Mechanical refining is commonly used to improve the limitations found in recycled fibers and to develop desired properties in virgin fibers. At the same time that refining increases tissue strength, it also decreases bulk and water absorbency.

REFERENCES CITED

Agnihotri, S., Dutt, D., and Tyagi, C. H. (). “Complete characterization of bagasse of early species of Saccharum officinerum-CO for pulp and paper making,” BioResources5(2), -. DOI: 10./biores.7.4.-

Axelsson, B. (). “Pulp for high absorption tissue products,” Paper Technology 42(7), 24-26.

Beuther, P. D., Veith, M. W., and Zwick, K. J. (). “Characterization of absorbent flow rate in towel and tissue,” Journal of Engineered Fibers and Fabrics 5(2), 1-7.

Bhatia, K., Peterson, R. C., Sommer, A. J., and Waller, M. H. (). “Use of near infrared spectroscopy and multivariate calibration in predicting the properties of tissue paper made of recycled fibers and virgin pulp,” Miami University.

Bonomi, A., Mariano, A. P., Jesus, C. D. F. de, Franco, H. C. J., Cunha, M. P., Dias, M. O. S., Chagas, M. F., Cavalett O., Mantelatto, P. E., Maciel Filho, R., et al. (). “The virtual sugarcane biorefinery,” Retrieved from http://ctbe.cnpem.br/en/research/integrated-evaluation-biorefineries/

Boudreau, J. (). “New methods for evaluation of tissue creping and the importance of coating , paper and adhesion,” Karlstad University.

Boudreau, J., and Germgard, U. (). “Influence of various pulp properties on the adhesion between tissue paper and yankee cylinder surface,” BioResources 9(2), -.

Brown, S. R. (). “Overview of tissue finishing and converting,” TAPPI Journal, 74(10), 91-94.

Byrd, M., and Hurter, R. (). “Considerations for the use of nonwood raw materials for tissue manufacture,” in: Paper Con , TAPPI Press, Atlanta.

Cao, S., Ma, X., Lin, L., Huang, F., Huang, L., and Chen, L. (). “Morphological and chemical characterization of green bamboo (Dendrocalamopsis oldhami (munro) keng f.) for dissolving pulp production,” BioResources 9(3), -. DOI: 10./biores.9.3.-

Council of Europe. (). “Policy statement concerning – Tissue paper kitchen towels and napkins”.

De Ruvo, A., and Htun, M. (). “Fundamental and practical aspects of paper-making with recycled fibers,” in The Role of Fundamental Research in Paper Making, J. Brander (ed.), Mechanical Engineering Pub., Ltd., London, Vol. 1, 195-225.

Enderby, S. A., and Straten, T. J. Van. (). “Two-ply paper products with either nested or foot-to-foot embossment and method of making,” United States Patent 6,261,666.

Espy, H. H. (). “The mechanism of wet-strength development in paper: A review,” TAPPI Journal 78(4), 90-99.

Euromonitor. (). “Market size of tissue products,” Euromonitor International.

FAO, F. D. (a). “Forest products definitions,” Retrieved from http://www.fao.org/forestry/-b3cfd87fda2bb.pdf51da2bb.pdf

FAO, F. D. (b). “Forestry production and trade,” Retrieved January 1, , from http://www.fao.org/faostat/en/#data/FO

Fisher, R. (). “Global tissue market overview,” in: Tissue Day – Emerging Technologies in The Tissue Industry, NC State University, Raleigh.

FisherSolve International. (). FisherSolve Database.

Foelkel, C. (). Advances in Eucalyptus Fiber Properties & Paper Products. International Colloquium on Eucalytus Pulp, Retrieved from http://www.celso-foelkel.com.br/artigos/outros/Advances in euca fiber.pdf

Forbess, D. L. (). “Wet end chemistry in towel and tissue,” in: Tissue Runnability Short Course (pp. 25-46).

Gentile, V. R., Hepford, R. R., Jappe, N. A., Roberts Junior, C. J., and Steward, G. E. (). “Absorbent unitary laminate-like fribrous webs and method for producing them,” United States Patent 3,879,257.

Gigac, J., and Fišerová, M. (). “Influence of pulp refining on tissue paper properties,” Tappi Journal 7(8), 27-32.

Gonzalez, R., De Assis, T., Wang, Y., Phillips, R., Pawlak, J., Dasmohapatra, S., Jameel, H., Kavalew, D. (). “Mapping drivers for value in the tissue & towel industry,” in: Tissue Day – Symposium on Fiber Development, Sourcing, Trends and Innovation, NC State University, Raleigh, NC.

Göttsching, L., and Stürmer, L. (b). “Physical properties of secondary fibers under the influence of their previous history. Part 2: Influence of multiple recycling,” Wochenbl. Papierfabr.106(23/24), 909-918.

Grivas, S. S. (). “Impact of recycled fiber on sheet forming,” Tappi Journal 75(4), 139-147.

Hall, C. (). “Eucalyptus pulp for tissue,” Paper (London)200(9), 32-36.

Hollmark, H., and Ampulski, R. S. (). “Measurement of tissue paper softness: A literature review,” Nordic Pulp And Paper Research Journal 19(3), 345-353.

Hubbe, M. A. (). “Bonding between cellulosic fibers in the absence and presence of dry strength agents – A review,” BioResources 1(2), 281-318. DOI: 10./biores.1.2.281-318

Hubbe, M. A., Venditti, R. A., and Rojas, O. J. (). “What happens to cellulosic fibers during papermaking and recycling? A review,” BioResources 2(4), 739-788. DOI: 10./biores.2.4.739-788

Hubbe, M. A., Ayoub, A., Daystar, J. S., Venditti, R. A., and Pawlak, J. J. (). “Enhanced absorbent products incorporating cellulose and its derivatives: A review,” BioResources 8(4), -. DOI: 10./biores.8.4.-

Hubbe, M. A. (). “Prospects for maintaining strength of paper and paperboard products while using less forest resources: A review,” BioResources 9(1), -. DOI: 10./biores.9.1.-

Hyman, M. R., Kopf, D. A., and Lee, D. (). “Review of literature – Future research suggestions: Private label brands: Benefits, success factors and future research,” Journal of Brand Management 17(5), 368-389. DOI: 10./bm..33

Jang, H. F., Howard, R. C., and Seth, R. S. (). “Fiber characterization using confocal microscopy – Effects of recycling,” Tappi J. 78(12), 131-137.

Johnsson, G. E. (). “Mechanical pulp in tissues, fine papers, and boards,” Paper Age 14(5), 14-15, 23-24, 31-34.

Kan, C. W., Leung, M. H.-M., and Mongkholrattanasit, R. (). “Tensile properties analysis of paper towels,” Applied Mechanics and Materials 848, 162-165. DOI: 10./www.scientific.net/AMM.848.162

Kan, C. W., and Wong, M. L. (). “A study of paper towel hand properties,” AATCC Review 15(5), 38-47. Retrieved from http://www.scientific.net/AMM.848.162

Kilby, E., and Crevecoeur, A. (). “Pulp and paper industry – Definitions and concepts,” Retrieved from http://www.cepi.org/node/

Kim, J. J., Shalev, I., and Barker, R. L. (). “Softness properties of paper towels,” Tappi Journal 77(10), 83-89.

Klerelid, I. (). “Drying section for drying a paper web in a papermaking machine,” United States Patent 6,488,816.

Kullander, J. (). “Evaluation of furnishes for tissue manufacturing,” Karlstad University.

Kullander, J., Nilsson, L., and Barbier, C. (). “Evaluation of furnishes for tissue manufacturing ; suction box dewatering and paper testing,” Nordic Pulp & Paper Research Journal 27(1), 143-150. DOI: 10./npprj--27-01-p143-150

Leponiemi, A. (). “Fibres and energy from wheat straw by simple practice,” VTT Publications, Aalto University.

Lindström, T., Wågberg, L., and Larsson, T. (). “On the nature of joint strength in paper – A review of dry and wet strength resins used in paper manufacturing,” in: 13th Fundamental Research Symposium (pp. 457-562). Cambridge.

Liu, J. (). “Effects of chemical additives on the light weight paper,” Georgia Institue of Technology.

Loebker, D., and Sheehan, J. (). “Paper towel absorptive properties and measurement using a horizontal gravimetric device,” in: PaperCon , Covington, TAPPI Press, Atlanta, pp. -.

Lois-Correa, J. A. (). “Depithers for efficient preparation of sugar cane bagasse fibers in pulp and paper industry,” Ingenieria Investigacion Y Tecnologia 13(4), 417-424.

Maloney, T. C., Li, T.-Q., Weise, U., and Paulapuro, H. (). “Intra- and inter-fiber pore closure in wet pressing,” Appita J.50(40), 301-306.

McKean, W. T., and Jacobs, R. S. (). “Wheat straw as a paper fiber source,” The Clean Washington Center, Domtar Inc., Retrieved from http://www.cwc.org/paper/pa971rpt.pdf

McKinney, R. W. J. (). Technology of Paper Recycling, Firs Ed., Blackie Academic & Professional, Glasgow.

Muller, G. A., and Teufel, G. (). “The use of reclaimed fibre in tissue manufacture,” Paper Technology 14(3/4), T146-T149.

Nanko, H., Button, A., and Hillman, D. (). The world of Market Pulp, C. E. Swann, Ed., Appleton, Wisconsin, USA: WOMP, LLC.

Neal, C. W. (). “Wet end chemistry of tissue paper,” in: Tappi Tissue Seminar, pp. 43-51.

Norwegian Pulp and Paper Research Institue. (). “More mechanical pulp in modern soft tissue,” Norsk Skogindustri37(7/8), 18-19.

Novotny, R. J. (). “Mechanical and chemical methods enhance tissue sheet properties,” Pulp and Paper 62(8), 74-78.

Page, D. H. (). “A theory for the tensile strength of paper,” TAPPI Journal 52(4), 674-681.

Pavan, P. C. (). “Tailoring eucalyptus fibre for tissue paper production,” in: 5th International Colloquium on Eucalyptus Pulp, Porto Seguro – BA, Brazil.

Peters, J. (). “Advanced fiber management for improved tissue machine productivity and quality,” in; PaperCon , TAPPI Press, Atlanta.

Phillips, R. B., Chang, H. M., and Jameel, H. (a). “Technical / economic analysis of bamboo fiber in pulp and paper manufacture – Part I. Economics of growing bamboo in a plantation for biomass production,” in: TAPPI PEERS, TAPPI Press, Atlanta.

Phillips, R. B., Naithani, V., Chang, H. M., and Jameel, H. (b). “Technical / economic analysis of bamboo fiber in pulp and paper manufacture – Part 2. Economic potential for bamboo utilization in an uncoated freesheet mill,” in: TAPPI PEERS, TAPPI Press, Atlanta.

Pöyry. (). “Changing patterns in the global tissue market: Private label versus brands,” Pöyry, retrieved from http://www.poyry.com/sites/default/files/media/related_material/_private_label_and_brands_-_global_market_dynamics.pdf.

Rainey, T. J. (). “A comparison between highly depithed and conventionally depithed bagasse pulp,” APPITA Journal 65(2), 178-183.

Raunio, J.-P., and Ritala, R. (). “Simulation of creping pattern in tissue paper,” Nordic Pulp and Paper Research Journal 27(2), 375-381. DOI: 10./NPPRJ--27-02-p375-381

Reisinger, L. (). “Technology trends in tissue making,” in: Tissue Day – Emerging Technologies in The Tissue Industry, NC State University, Raleigh. DOI: 10./978-3-319--1

Roncero, M. B., Torres, A. L., Colom, J. F., and Vidal, T. (). “TCF bleaching of wheat straw pulp using ozone and xylanase. Part A: Paper quality assessment,” Bioresource Technology 87(3), 305-314. DOI: 10./s-(02)-9

Roy, T. K., Subrahmanyam, S. V., Godiyal, R. D., Panda, A., and Pant, R. (). “Effect of nonfibrous tissue on the papermaking properties of bagasse and straws,” in: Annual General Meeting & Seminar on Nonwood Fibrous Raw Materials for Pulping and Papermaking – IPPTA, IPPTA, New Delhi, pp. 49-55.

Sanford, L. H., and Sisson, J. B. (). “Process for forming absorbent paper by imprinting a fabric knuckle pattern thereon prior to drying and paper thereof,” United States Patent 3,301,746.

Singh, S., Dutt, D., and Tyagi, C. H. (). “Complete characterization of wheat straw (Triticum aestivum PBW-343 L. emend. fiori & paol.) – A renewable source of fibres for pulp and paper making,” BioResources 6(1), 154-177.

Smurkoski, J. A., Leggitt, G. L., and Wilson, G. L. (). “Papermaking belt and method of making the same using a textured casting surface,” United States Patent 5,098,522A.

Springer, A. M., and Pires, E. C. (). “Combined effect of fiber fines and dissolved organics on tissue properties,” TAPPI Journal 71(4), 141-144.

Subrahmanyam, S. V., Godiyal, R. D., Sharma, A. K., Vipul, J. T., and Gupta, H. K. (). “Effect of refining energy on the pulp properties of nonwoods,” IPPTA 12(2), 11-18.

Sundholm, J., and Huostila, M. (). “Can TMP and CTMP be used in tissue paper,” Pulp and Paper Canada 81(3), 60-62-68.

Thorp, B. A. (). Pulp and Paper Manufacture – Volume 7: Paper Machine Operations, M. J. Kocurek (ed.), 3rd Ed., Atlanta, GA, USA; Montreal, Quebec, Canada: Joint Textbook Committee of the Paper Industry .

Tprint. (). “TPrint marketing plan,” Retrieved from https://josenzhong.files.wordpress.com//01/toilet-paper-marketing-plan.pdf

Trepanier, R. J. (). “Pulp fiber quality and the relationship with paper tissue properties,” in: Tappi Tissue , TAPPI Press, Atlanta, pp. 1-30.

Tysén, A. (). Through Air Drying – The Influence of Formation and Pulp Type on Non-Uniform Drying and Air Flow. Karlstad University.

Valmet. (). “Advantage TM NTT ® technology – Tissue with high bulk and softness,” Retrieved from http://www.valmet.com/NTT/

Voith. (n.d.). “ATMOS – Advanced tissue molding system,” Retrieved from http://voith.com/corp-en/papermaking___atmos.html

Wang, Y., and Chen, Y. (). “Application of high-consistency refining to enhance tissue performance and tissue machine runnability,” in: Paper Con , TAPPI Press, Atlanta.

Watson, P., and Janssen, W. (). “High quality NBSK fibre for premium tissue paper grades,” Tissue World Magazine.

Wendt, G. A., Chiu, K. F., Burazin, M. A., Farrington Jr., T. E., and Heaton, D. A. (). “Method of making soft tissue products,” United States Patent 5,746,887A.

Wrap. (). “Specifying recycled content in tissue paper for your organisation,” Retrieved from http://www.wrap.org.uk/sites/files/wrap/Tissue paper.pdf

Yuan, Z., Jong, J., and Larivière, S. (). “High-yield pulp in tissue and towel,” PaperCon , TAPPI Press, Atlanta.

Zou, X. (a). “Overview of tissue grades and their pulp furnish selection,” in: PaperCon , Minneapolis, TAPPI Press, Atlanta, pp. 1-28.

Zou, X. (b). “Refining of HW and SW kraft for tissue making,” in: PaperCon .

Zou, X., and Liu, H. (). “Review of non-wood fibres and their applications in tissue,” in: PaperCon , TAPPI Press, Atlanta.

Article submitted: November 15, ; Peer review completed: December 18, ; Revised version received: March 21, ; Accepted: March 22, ; Published: March 27, .

DOI: 10./biores.13.2.DeAssis

Contact us to discuss your requirements of Bottom Pull Facial Tissue Paper Production Line. Our experienced sales team can help you identify the options that best suit your needs.

Previous: None
Next: None

Comments